Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

PM45 headstock riser ......

Posts

PM45 headstock riser ......

#1

PM45 headstock riser ......

Brian Roberts

The project is going well!

Headstock riser made from some more 2" scrap aluminum (MIC6® Aluminum Cast Plate).

Programmed to drill the holes for SHCS's and locating pins and machine out the the inside areas. The outside was not so easy! Powermatic didn't waste any time on making things square....or pretty. so...pinned and screwed the riser to the headstock....

....scratched a line around it and took it apart and bandsawed to the line. Then screwed it back together and took it to the Powermatic belt/disc sander to finish it to the headstock.







I may fill the gaps between the two after it's bolted to the lathe...and prior to final paint.

All in all...moving along quite nicely...

To all the naysayers....I don't do it to make money....or to make "new" out of old...I do it to keep the brain working and because IT"S FUN!!!!

Thanks for looking!

Brian

Re: PM45 headstock riser ......

#2

Re: PM45 headstock riser ......

Don Evans

Nice looking job and well done.

I've rebuilt several old iron metal lathes complete disassemble, sand blast to bare metal, polish all unpainted area and replace and defective parts. You are right it is fun.

Don

Re: PM45 headstock riser ......

#3

Keith Tompkins

Re: PM45 headstock riser ......

Keith Tompkins

Beautiful job! You should be rightfully proud!

Re: PM45 headstock riser ......

#4

Re: PM45 headstock riser ......

Don Orr

Great work on both parts. I'm jealous that you have the knowledge and access to do this. Enjoy your "new" lathe and its capabilities!

Re: PM45 headstock riser ......

#5

Thanks to all....more

Brian Roberts

to follow as time allows for progress!

Brian

Re: PM45 headstock riser ......

#6

Re: PM45 headstock riser ......

Pete in Holland MI

It's often not the cost & value of the project outcome, but the journey to get there that is the enjoyment.

Pete

Re: PM45 headstock riser ......

#7

Re: PM45 headstock riser ......

Keith Newton

Great job Brian. I have one of those, and went through pushing it past it's limits, and can share some of the problems I faced, and how I tried to solve each, only to find the next weakest link.

I did most of my vessel turning outboard. First, I installed a 3 hp 3ph motor to give enough power to deal with large cutting diameter. THen I bolted on 1" thick steel plates to both ends of the base, with flair to widen the stance. But still, the next weakness, is where the cast headstock bolts onto the steel base, is not sufficient, because the 1/4" steel angle will flex, and I would expect your riser, only gives a longer lever arm to work against.

Also, the little finger size casting above the outboard bearing had me worried after having to replace the bearing a couple of times, needed shims around the outer bearing race. Rather than waiting for that to fail, was about the time I found the castings for my big lathe. The headstock was from a railroad shop, and looked like it was set up to turn the wheel assembly. It has 4.5" diameter solid steel arbor, with double rows of tapered roller bearings on each end about 20" apart, and weighs 3000#.

Re: PM45 headstock riser ......

#8

Re: PM45 headstock riser ......

Brian Roberts

Hi Keith...

Thanks for the input!

That tiny outboard (compared to the inboard) bearing really makes no sense does it? It should be bigger than the inboard bearing....but I get the cost vs perceived value thing.

The base does leave much to be desired. The area where the cast head bolts to the cast bed is plenty strong....I believe. But where the bed bolts to the base is....you are correct...one of the weak points!

Having turned on this old timer for many years, I just think back to what I wanted it to do....that it couldn't as it was from the factory.

Mainly....a couple extra inches of swing....for the clock frames and platters I was doing at the time........and a way to reduce the speed to less than the 600 rpm minimum offered by the step pulleys.....which was WAY too fast for big or unbalanced projects.

I understood that the limitations would remain....or get worse IF I pushed too hard.

I gotta say....you have more guts than I do....a 3HP motor....that's crankin some torque!

I really had enough with the 1 HP that was on mine.....BUT I wasn't making my living with it so slower was OK.....if, admittedly, frustrating at times.

Your BIG lathe sounds like the ticket! How much space does it fill? Any pics?

Re: PM45 headstock riser ......

#9

Re: PM45 headstock riser ......

Keith Newton

Brian, it sounds like for your needs, this should be great. I was turning green wood 12" ~ 14" D, X up to 16" tall, many with natural edge, where things were naturally out of balance.