Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Casting resin *LINK*

Posts

Casting resin *LINK*

#1

Casting resin *LINK*

David Walser

Australian Brendan Stemp, on his Youtube channel, shows how he uses epoxy resin to make turning blanks. He makes fairly large blanks -- such as pepper mill blanks and bowl blanks. He uses Solid Cast 606 resin, from Solid Solutions, for casting his blanks. An advantage of the resin is its relatively long open time, which allows the time needed to pour larger blanks. Also, the long open time allows any air bubbles to migrate to the top of the resin before the resin hardens. This avoids the need to cast the blanks under pressure. Also, the resin does not produce a lot of heat when hardening, allowing larger blanks to be cast. (Sometimes Brendan uses two pours for a blank to avoid the excess heat that would be generated if a really large blank were cast at once. To do this, he pours half the blank and allows it to set up but not cure completely before pouring the second half. This approach produces a seamless blank.)

I don't believe Solid Cast 606 is available in the USA. Question: Can any of you recommend a resin available in this country that could be substituted for Solid Cast 606? The bowls Brendan produces are spectacular and I have a lot of off cuts that I'd like to use up.


Making bowl blank with scraps of wood and resin

Re: Casting resin *LINK*

#2

Re: Casting resin

David Paine

I have used two types of resin in turning projects

System Three

Amazing Clear Cast Resin

System Three requires careful measurement of resin and hardener. It is a 2 of one to 1 part of the other mix. If the mix ratio is off, the resin will not set.

I have used this two or three times. In each case I have had bubbles, which end up as small holes when you turn.

Amazing Clear Cast Resin is a 1 - 1 mix ratio and not as critical a mix.

The claim is that there will be no bubbles. I have only used this once. The bubbles did clear better than with System Three. In my shaping I did not expose any holes.

The product is claimed to be clear when cured.

The president of my local turning club used this for an inlay on a rim of a bowl with small sea shells in the resin. It did cure clear and buff to a clear surface. The president said another Amazing resin did not buff clear.

I hope this helps.

Re: Casting resin *LINK*

#3

Re: Casting resin

John Lucas

I've used Cast-n-Craft. Sounds like it works the same as what Brendan uses. I've used it for several projects.

Re: Casting resin *LINK*

#4

Re: Casting resin *LINK*

Dick Coers

Penturners mainly use two resins, Alumilite which is urethane with a very quick set time but is not brittle like polyester resin. And polyester resin and most buy Silmar 41 from US Composites.


Silmar 41

Re: Casting resin *LINK*

#5

Re: Casting resin *LINK*

Jeff Willaford

IIRC Alumilite is used when embedding wood as it adheres better than poly resin.

Take a look on the penturners form for detailed information about casting.

Marilyn Campbell also uses West System epoxy in some of her work.


http://www.penturners.org/forum/index.php

Re: Casting resin *LINK*

#6

Re: Casting resin

Dale Gillaspy

David, I know your Saturday's have been dedicated to family and church commitments as of late, but if you can make the meeting this week, Ken Northern is doing a demo on casting and using part burl/part resin to make blanks. He is also going into how to make a very inexpensive vacuum chamber.

Re: Casting resin *LINK*

#7

Re: Casting resin

David Walser

Dale -- I wish I could be there. This month's excuse is that I'll be out of state for my father's 90th birthday celebration. (Those who know me might reasonably wonder how someone with my apparent youth and vitality could have a father that's 90 years old. Let's just say Dad was old when I was born. Very old.)

Re: Casting resin *LINK*

#8

Re: Casting resin

Bill Jacksonville, NC

I wanted to turn a wood pen with watch components and clear finish and did not want to fool with Silmar 41 or Alumilite resins and molds.

So was looking at a product online called #2232 Crystal Sheen Pour On Finish. They sell different formulations, but #2232 at Creative Wholesale lot less expensive than 41 or alumilite. I never got around to getting required watch components so never used the product myself. Depending upon your project might be worth a look.

Re: Casting resin *LINK*

#9

Re: Casting resin

Curt Stivison

I have used both Aluminte and Similar 41. If using Similar you need alot of ventilation. Most people who do casting use a pressure camber at 70 lbs. to remove bubbles form the casting.

Re: Casting resin *LINK*

#10

Re: Casting resin

TomB

Here is the one I have been looking at to do some casting in a deep bowl rim

http://www.alchemie.com/category/products/polyurethane-resin/water-clear-resin/?page=1

I have not yet pulled the trigger on tho....