Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

decorative rosette on tool handle

Posts

decorative rosette on tool handle

#1

decorative rosette on tool handle

eliot feldman

A friend made me some tool handles that hand tiny decorative brass rosettes at the end of the handles right in the center. Very sadly, he passed away so that I never had the chance to ask him how he did that part of it. Do you know how it's done?

Re: decorative rosette on tool handle

#2

Re: decorative rosette on tool handle

Brian Roberts

Pictures?

Re: decorative rosette on tool handle

#3

Re: decorative rosette on tool handle

eliot feldman

I've never been successful with pictures on this site.

Just picture something like a small four leaf clover about 1/4 inch diameter made of brass centered on the tool handle at the very end.

Re: decorative rosette on tool handle

#4

Re: decorative rosette on tool handle *LINK*

Stuart Johnson

It sounds like he might have used a brass tack of some sort. Either tap it in place or drill a small hole and inset it with some epoxy.


Brass Tacks

Re: decorative rosette on tool handle

#5

Re: decorative rosette on tool handle

Bruce Pratt

I've seem something similar done with rivets on knife handles. It was done with various very small diameter brass, copper and aluminum rods set into black epoxy.

Re: decorative rosette on tool handle

#6

Re: decorative rosette on tool handle

eliot feldman

Ah, ha! That's exactly what it looks like. I was hoping for something easier to do. (I got some decorative tacks. but it doesn't look anywhere so good.)

Now here's my problem. When I turn a tool handle, It's all done between centers; the blank never goes into a chuck. So, to insert these rods, sand, finish, etc. properly, I need to have access to the very end of the tool handle while it's turning; and I really am not sure how to hold a fairly long tool handle so it doesn't wobble while I am working on the very end. I don't want to fool with steady rests, etc. just for this. Any thoughts?

Re: decorative rosette on tool handle

#7

Steven Antonucci

How bad do you want it?

steven antonucci

For starters, you can make your own or just buy them from the knife supply catalogs (Texas Knife/Jantz). The more involved they are, the more they cost.

If you want to make your own, you need an assortment of stuff (various wires and tubes), and colored epoxy. If you make your own, it can be any diameter you can imagine... and any material. (various wood metal combos?)

Once you have a rod made, you'll want to use your chuck to accurately drill the end for the rod. You can use colored epoxy to set it in. depending upon the diameter of the rod, you can reverse it in the chuck and hold it in a small set of jaws or a drill chuck to finish turning your handle.

Re: decorative rosette on tool handle

#8

Re: decorative rosette on tool handle

walta

This is how I turn a handle.

1 Cut a blank 2 inches longer than the finished length.

2 Drill a hole to fit tool in one end. I prefer to drill on the lathe thru the center of a hollow live center with a long bit.

3 Grip about ½ inch of the square blank in the chuck.

4 Put the tail stock live center in the hole.

5 Near the tail stock turn to fit my copper feral.

6 Turn the handle to fit my hand.

7 Sand and wire burn a few lines.

8 Part the handle off near the chuck.

9 Sand where you parted off.

10 Make 2 saw cuts in the end under where the feral will be.

11 Hammer on the feral. It should be very tight.

12 Put some yellow glue in the hole, insert the tool some glue should come out the top. Warning the only way to remove the tool from the handle it to cut the handle into ½ inch rings and break them.

13 Finish if desired I prefer the feel of raw wood over any finish.

Please post a photo of your rosette.

Walta