Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

working on a video

Posts

working on a video

#1

working on a video

John Lucas

I'm doing a short video for the AAW on skew cuts and will be discussing why it catches. I was teaching a few guys yesterday and it occured to me that most catches are 3 things. One is trying to use an unsupported edge. (and Lyle did a great article on this several years ago) Typically this would be touching one of the upper wings on a spindle roughing gouge to the wood where the lower U is on the tool rest. Since that wing is unsupported the wood tries to pull it down to that support and pulls it into the wood and you get a catch. The same would be true for the wing of a bowl gouge if you have the flute up. With the skew it's letting the cut get too high on cutting edge so you can't defeat the leverage of the wood coming into it and it pulls the skew into the work. Cutting below the center line on the skew prevents this from happening. If you are cutting into a shoulder or a bead and you have the bowl gouge flute at about 45 degrees the wing that hits that shoulder will be pulled down rapidly since it's unsupported by the tool rest. In that case I simply rotate the flute toward the shoulder so the lower wing of the gouge is now touching the tool rest. It is now supported so it won't catch if it hits that shoulder or bead.

The second is simply coming off the bevel. Usually on the skew it's lifting the handle so only the cutting edge is engaged in the wood. On a bead it's usually because you move the handle faster than the edge can cut around the bead so the bevel looses contact and you get that spiral catch. With a bowl gouge you steer with the handle and it usually means that you didn't guide the bevel along the curve of the wood. Push the handle one way and it stops cutting because the bevel is rubbing but the edge isn't touching. Push it the other way and the bevel isn't rubbing and the edge tries to cut too deep and you get a catch.

If you can imagine scooting a shovel across the ground. If the whole back of the shove is rubbing the ground you don't get a cut. Lift the handle slightly and you start lifting soil. Lift it more (where the back or bevel is not touching) and you dig in too deep and the shovel stops. If the ground was moving toward you it would be just like a catch. The handle of a shove is a very good example of how you guide a bowl gouge so the bevel or back of the shovel controls the shape of the cut.

The last reason is inattention. What happens is you touch the wood with the tool without it being on the tool rest. It of course snaps the tool down real fast and sometimes even breaks the tool rest. I see this a lot. Always pay attention when the tool is anywhere near the wood.

I need to do a video on that. Maybe after this move I can get it done.

Well gotta go to town and sign some more papers and hopefully re-purpose some found boxes.

Re: working on a video

#2

Re: working on a video *LINK*

David Walser

John, I wish you luck with both the move and the upcoming video. I look forward to seeing it.

Brian Havens has a video teaching the peeling cut with the skew. In the beginning of the video, he does a clear job explaining why many turners find the skew so hard to master. (It's your first reason for a catch.) In all the skew videos I've seen, I don't recall the concept being taught as clearly as Brian does in his video.


Brian Havens on the peeling cut

Re: working on a video

#3

Re: working on a video

Scot in Falcon

Not to suggest you don't make your own video, but Richard Raffan does a pretty good job of explaining this as well if you haven't seen it already:

https://www.youtube.com/watch?v=jOvF5f1phhY

Re: working on a video

#4

Re: working on a video

Sergio

Raffan' video is excellent. You have a challenge there.

Re: working on a video

#5

Re: working on a video

John Lucas

Nice video. One of the reasons I prefer a straight cutting edge is I can cut the tenon square without ever flipping the tool. It's interesting that he does his final cut with a peeling cut. I find that a planing cut will leave a much cleaner finish.

Re: working on a video

#6

Re: working on a video

John Lucas

I've seen Richards. It is excellent as of course is all of his work. I made the video to support an Article by Keith Thompkins for an upcoming article in American woodturner.

Re: working on a video

#7

Re: working on a video

John Lucas

Wouldn't even try to compete with Richard. He is a great guy, fabulous turner, and fabulous teacher.

Re: working on a video

#8

Keith Tompkins

Re: working on a video

Keith Tompkins

Nice guy too! :)

Re: working on a video

#9

Alan Lacer Skew

John Lucas

Alan's skew chisel starts with a flat area near the long point and then curves down. This is a much better better design for peeling cuts. When doing tenons you use the flat area and cut down however many times it takes to get your tenon length. Then slide it along the tenon like Brian does on the long cuts to really make the sides parallel.

I typically use a Bedan to cut my tenons. I part down using the peeling cut and then swing the Bedan sideways to give a very clean peeling cut for final size on the tenons.

Lots of different ways to skin a cat and each of us finds what works best for out tools.

Re: working on a video

#10

Mike Stafford

Re: working on a video

Mike Stafford

Both Richard Raffan and Alan Lacer have excellent videos on the skew and how to use it while avoiding catches.

That is not to say that you will not do an excellent job. Your videos are always excellent additions to anyone's woodturning instructional library.