Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Be careful

Posts

Be careful

#1

Be careful 

John Lucas

Well I really wasn't in danger because my hands were well out of the way and my body was balanced. Apparently the bottom wasn't as flat as I thought it was and my blade wasn't as sharp as it should. So when the wood rocked a tiny bit and the blade was already trying to wander it popped the blade off the wheels.

The blade wasn't damaged and I wanted to save it even though it's getting dull. It's fine for cutting 6" deep bowl blanks just not good for 15". I drove chisels and wedges in until it popped the slab of wood off and I could retrieve the blade. It is a nice walnut crotch and I really didn't want to lose it.

So ideally you should make sure any surface touching the table is flat or has been wedged on a wooden sled to make sure it can't rock. And of course you should use a sharp blade.


Re: Be careful

#2

Brad Vietje

Glad You Weren't Hurt, John!

Brad Vietje

Glad you were not hurt, John.

On a related band saw safety note, I see all kinds of people cutting a blank round on the band saw with the SMALL (bark) side down ! What the heck is up with that? I have a bunch of rounds cut from pine boards or plywood to help cut out circles - 8", 9", 10", 12", etc... with a nail hole at center to attach them to the blank. Now why would I cut around this guide with the big side up, instead of the big (read: STABLE) side down ?!? Beats me, but I see people do what looks mighty dangerous to me.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Be careful

#3

Re: Be careful

Sergio

Judging from the picture, which might give a parallaxis illusion, the blade looks a little small for that size log.

Re: Be careful

#4

Re: Be careful

robo hippy

Like Sergio said, that blade looks a little thin for ripping that height. My big saw has a 1 1/4 by teeth at 3/4 inch apart. I lay the flat side down and square up one end, then stand it up on end and cut the slabs with parallel sides. I learned the hard way not to use dull blades. 4 stitches.....

robo hippy

Re: Be careful

#5

Exactly how I cut things Brad

John Lucas

ngs

Re: Be careful

#6

It's 1/2" 3TPI.  Done this cut before


Re: Be careful

#7

Be careful

Sergio

A band saw is mainly intended for cross cutting. Ripping can be done of course but it puts a lot of stress on the blade. The higher the wood the larger should be the blade. 1/2 inch is a small blade good for general cross cutting in small to medium pieces. It does not have the rigidity to cut safely bigger logs particularly in ripping mode.

The thickness of the blades starts to increase at 3/4 inch: a 1/2 inch blade is usually 0.025 inch thick like the smaller ones, a 3/4 is 0.032 inch and a 1 inch is 0.035. This allows for much more tension and rigidity necessary for larger logs.

Re: Be careful

#8

Re: Be careful

robo hippy

Well, the tooth set and shape is important for ripping and cross cutting, which is why there are ripping saw and blades which have larger teeth farther apart, and cross cutting blades which have teeth closer together. Of course, there are combination blades as well. The biggest problem I have when I rip on my bandsaw are the hair balls that form inside. I put a vent in the bottom part of the door in my big saw (Laguna 16HD with 4.5 hp motor), and that works far better than the around in the back corner. You would think, by the dust collection ports on the bandsaws that they were designed for cabinet shops and not for cutting green bowl blanks.... Going to do a video on that some day....

robo hippy

Re: Be careful

#9

Re: Be careful

John Lucas

I do have a larger blade but rarely use it. The 1/2" does 99% of everything I need to do including 15" deep cuts. You just have to take it slow. I agree if your going to cut very many pieces deeper than 12" you should change to a larger blade but then you can't turn tight corners. I make hollow vessel blanks that are about 8" around and 12" tall and you just can't do that very well with a 3/4" blade.

I use my 1/2" blade frequently to cut out hollow form blanks that are 10 to 12" deep. When it's sharp it does it easily on this saw. On my older Delta with the riser block it was kind of iffy.

I saw a tip the other day where they suggested narrowing the back of the blade to make it track around corners. Not just rounding over the back corner but actually narrowing maybe the last 1/4" by tapering both sides and then rounding the back edge. Anyone tried this. Next time I put my big blade on I may do a test and see.

Re: Be careful

#10

Re: Be careful

Ron Bauer

John, If the back is tapered in any fashion I would be concerned about its' effect on the thrust bearing/block on the backside where the thinning could cause undesirable grooving. Just my opinion. Ron.

Re: Be careful

#11

Steven Antonucci

The dull blade is the bad guy

steven antonucci

probably wasn't clearing the cut, a little build up, a little wander... and all of a sudden the blade had stuff stuck to it and wasn't straight any more, and blammo... you are stuck!

I am with you. I usually have a 1/2" 3TPI blade on my saw. I just changed to a new blade after 2 years of cutting EVERYTHING (wet, flat, dry, plastic)... small kink once, but I cold set it out with two vise grips until it ran well again. Still sharp (enough) that I held on to it

S

Re: Be careful

#12

Dick Hines

Re: Be careful

Dick Hines

This is why I rough out all my big blanks with a chain saw. I had this happen once and it broke the blade. After that I use the chain saw.

Re: Be careful

#13

Re: Be careful

John Lucas

they mentioned in the article to round over the back to prevent any damage to the bearing. I would think if you do this on a thick blade the back would still be as thick or thicker than say a 1/4" blade so I don't think it would be a problem

Re: Be careful

#14

My blades are only $9

John Lucas

so I don't bother to resharpen or worry too much about a kinked or broken blade. I just toss them. In this case the blade still runs pretty true I'll use it to cut up the rest of the wood I'm now working with before I toss it.

This is wood meant for our club and I cut those round and under 12" for new turners. This one was a crotch piece and I left it larger because I know a couple of club members who love this sort of thing. Dying to keep it myself but with a possible move coming up I hate to move a lot of wood so I'm getting rid of as much as I can. Still there were drool marks on this one.