Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

New Dust Collection

Posts

New Dust Collection

#1

New Dust Collection

Steve Criscenzo

Last fall, while preparing for a gallery show, I spent several long days in the shop finishing pieces. In spite of being very careful with dust control ( I wear an Airstream while turning and I try to collect dust at the source with a 2 HP single stage dust collector) I was still feeling the effects of the prolonged exposure to the shop environment in my lungs. Since I am looking forward to retirement (and spending much more time in the shop) in three years I decided that I need to upgrade my shop dust collection system. I had two primary criteria. Fist it had to provide HEPA filtration and second it had to have sufficient power to use with two ports open at the same time.

After much research, I decided to go with the 3 HP “V” system from Oneida Air Systems. The added power allowed me to move it the dust collector to the far side of the shop (much quieter) but this move required a major redesign of my shop. I decided to go with metal ductwork because I am comfortable working with it and the ability to use 7” and 5” pipe in addition to 4” and 6” made for a more efficient duct design.

I finally had to chance to give it a run today. It works great. The first photo is a picture of the unit utilizing the wall mount system. The second photo is a wide shot showing the two dust hoods I currently use at the lathe. The third photo is a close in view of the dust hoods.

I use both hoods for most sanding operations. The front on is a 10x4 vent boot with three rare earth magnets holding it to the lathe. It captures most of the dust coming of the front of the piece when sanding and can be easily moved out of the way when not needed. The rear (PVC) dust port has a magnetic base that I usually fasten to the banjo while sanding. It hangs on a hook on the back of the lathe when not in use.

Even though the lathe is at the end of a 40 ft. duct run there is ample air movement with both ports open. Both ports are connected to individual 4” flex lines coming off a 6” trunk.

I think it will make a huge improvement.

I will post pics of the shop redesign in a separate thread.


Re: New Dust Collection

#2

Re: New Dust Collection

Barry Irby

I like it, Congratulations on the new setup.

May I suggest a couple of things to try? The boot you have on the front of the lathe appears to be a 4 X 10 or 4 X 12. Try a 2 1/4 X 10 or 12. The 4" version has four times the area of the air hose. This slows the air flow into the opening. This may cause the air to have less of a capture effect on the dust. The air needs velocity to overcome the momentum of a the dust particles.

Same thing on the back port. I think you will find one of the openings has much more flow that the other. Try using a "two by" boot there as well.

Also, I found it useful to look up duct parts on line and find the huge variety that are available. The Borgs only had the common ones. You can get the others at supply houses that supply HVAC installers. Look into an "End Boot", I have several in my shop and the were handy.

PS....Don't drop your sandpaper.

Re: New Dust Collection

#3

Re: New Dust Collection

Steve Criscenzo

Thanks for the suggestions Barry. I will look into the 10x2 boot for the front to increase velocity.

I have been using the PVC wye in the rear for several years and although the flow is a bit compromised by using the 4" fittings, the advantage is that I can position the ports just where I want them by rotating the front pieces. I can also position it to surround spindles and small boxes.

I also use end boots on several other tools. They work very well. I currently have my belt sander, bandsaw, and spindle sander connected. I am working on my table saw and I am building a hood to use when piercing and using my Foredom rotary tool.

I am fortunate to live near a major HVAC supplier so I have been able to get just what I needed. It makes a big difference to be able get heavier gage pipe and fittings locally. Not sure I would have gone with metal (vs PVC) if I had not found the supplier.

I am sure I will fine tune as I go along.

Thanks again for your suggestions

Steve

Re: New Dust Collection

#4

Re: New Dust Collection

don stephan

It's not designed for sanding spindles, but Reed Gray aka Robo Hippy has a Youtube video showing the sanding hood he uses. Looks like it is extremely effective when sanding bowls.

Re: New Dust Collection

#5

Re: New Dust Collection

Steve Criscenzo

I have seen Reed's dust hood and it looks loke it works great. I think it would take up too much space in my shop so I went with a simpler system.

Steve