Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Overheater Headstock

Posts

Overheater Headstock

#1

Overheater Headstock

Eric Knutsen

I have a Jet mini 1014 lathe. It doesnt see a tremendous amount of use but I've noticed recently the following problems:

1. the lathe doesnt immediately start when turning it on. I usually have to spin the headstock wheel to get it going.

2. It makes more noise that it used to.

3. The hand wheel tends to get hot.

I've adjusted the tension on the drive belt so I know that isnt the issue. I am thinking possibly there is bearing assembly in the headstock that needs lube? Replacement? I dont have a schematic for the lathe so anyone with advice, feel free.

Re: Overheater Headstock

#2

Re: Overheater Headstock

Phillip Medghalchi

Eric. this sounds like the problem John Lucas had with his BS motor and I had it too. I is inside the motor, it's the speed control switch. Mine used to get hot so sometimes you could smell the wire burning.

If you can replace it John an email to see if he can walk you through how you change it.

Here is one link

http://www.ereplacementparts.com/jet-jml1014i-708375-mini-lathe-parts-c-32652_32854_33061.html

and Jet manual link

http://www.manualslib.com/manual/79871/Jet-Jml-1014.html

Re: Overheater Headstock

#3

Dennis in Southern Oregon

Re: Overheater Headstock

Dennis in Southern Oregon

I would say that your first step ought to be to isolate the problem. Remove or completely loosen the belt and see if the motor starts normally and if there is any significant resistance in rotating the headstock. I am not familiar with the motor/drive set-up for that lathe (is it a VFD or a mechanical variable speed drive). Others here probably can help you further.

Dennis

Re: Overheater Headstock

#4

Re: Overheater Headstock

Dick Coers

Maybe too much preload on the bearings, or they are just plain worn out. Nearly everyone has to replace them with enough running hours. The hand wheel is used to preload the bearings through a spring steel washer. You can loosen the set screws on the hand wheel and loosen. Pretty sure they are left hand threads, but for some reason I don't remember for certain. It's very easy to replace the bearings, just don't get the cheapest ones you can find. Lots of info on the web for replacement.

Re: Overheater Headstock

#5

Re: Overheater Headstock

Eric Knutsen

Im figuring a bearing issue is the problem. Its not a variable speed lathe. I have to manually release the belt tensioner to move the belt to a higher or lower pulley. The motor seems fine, just a noisy and not exactly smooth running headstock. Ill look at the manual link that was posted to try and figure out how to open it up. I hate to send it out if its a relatively simply fix.

Thanks.

Re: Overheater Headstock

#6

Re: Overheater Headstock

Eric Knutsen

If anyone has a link which provides an exploded view forthe mechanical set up of the headstock, that would be great. The manual lists every part but no picture.

Re: Overheater Headstock

#7

Does the Handwheel move easily?

John Kaner

The handwheel is used to tension the spindle. Some folks use the handwheel to slow the lathe... This tightens it. Then the headstock gets hot to the touch. If the handwheel doesn't move easily, there are two set screws. Often they wear and don't grip like they should. A little file work and you can dress them...

Hope this helps.

Re: Overheater Headstock

#9

Re: Does the Handwheel move easily?

Barry L Elder

ereplacementparts.com will have the schematic and everything else. They even have a forum which is watched over by some of their employees. Prices on parts are a heck of a lot lower than Jet's prices.

Re: Overheater Headstock

#10

Re: Does the Handwheel move easily?

Eric Knutsen

Thank you, thank you, thank you!

Re: Overheater Headstock

#11

Re: Not a tough Google search

Phillip Medghalchi

Eric, there you go it can't get any easier than that, but if you are planning on keeping that lathe for awhile then it may be worth your wile to buy aircraft quality bearing then you can get your money out of them. I am not sure where you live. There should be some suppliers close to you, if not drop me a note and i can give you the name of the guy here that you can buy it from and I call him to tell him to send it the cheapest way he can. He is been here in San Antonio, supplying all the air force bases and the aircraft repair industry.

Good luck with it.

Re: Overheater Headstock

#12

Re: Overheater Headstock

William Duffield

Your problem may be much simpler than that. In addition to the electrical speed control, that lathe also has a mechanical speed control, in the form of a pair of stepped pulleys. The set screw on the upper pulley can come loose, allowing the pulley to slide inside the head stock until it rubs up against the side of one of the bearings (the fixed part). This will cause all the symptoms you have described. The fix is to move the pulley back into alignment with the lower pulley and tighten the set screw. I've had that problem with the non-VS version of that lathe.

Re: Overheater Headstock

#13

Re: Overheater Headstock

Eric Knutsen

All the information is great. Thank you. Everything appeared to be in line, as there was no obvious damage to the belt. I disassembled the headstock and removed the bearing. The headstock bearing was pretty gummed up with sawdust and grease. I went to Fastenal and ordered 2 new bearings, which they ultimately order from Bearings Limited. The cost....... $5 for the pair. Jet wanted over $30.