Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On β€” Est. 1998

If you sell to woodworkers, your customers are already here

built my Seg-easy the last 2 days *LINK*

Posts

built my Seg-easy the last 2 days *LINK*

#1

built my Seg-easy the last 2 days *LINK*

John Lucas

It works perfectly. I cut 12-16-24 and 32 segment rings and nailed them first try. I made my angle guides out of plexiglass and wasn't sure if the angles were dead on because of the way I cut them. Apparently they were close enough. One of the guys in our club purchased the angles and I look forward to laying mine on to of his too see if there's any difference (other than length since I didn't have any way to measure theirs and had limited plexi for the project.

If your doing segmented work you need to give this a try. It works really well.


http://www.segeasy.com/index.htm

Re: built my Seg-easy the last 2 days *LINK*

#2

Re: built my Seg-easy the last 2 days

Phillip Medghalchi

John, that's great you were able to make your own. How did you cut the Plexi w/o getting it crack on you?

Re: built my Seg-easy the last 2 days *LINK*

#3

Re: built my Seg-easy the last 2 days

John Lucas

It's easy to cut with a carbide blade. I should have put my 80 tooth on. This one left a tiny amount of chipping on the edges but all I really needed was a straight edge, not a pretty one.

I used my homemade sliding table on my table saw. If i can clamp something to it I can cut any angle. I used a Vernier angle caliper I bought at Harbour Freight for $6. Apparently the angles are dead on. It has readouts every 5 degrees. The scale tells you how many inches to set the bottom caliper to get the angle you want. Setting for 11.25 and 22.5 was interesting. I had to do a little math to find the setting but got close enough to work. I clamped the plexi to the angle and then scratched a line. Layed it on my sliding cut off jig and clamped it down with the scratch line flush with the edge of my sled. Apparently it worked.

Below is a photo showing the jig, the angles, a wooden spacer needed because my angles were too narrow and samples of the 12, 16, 24, and 32 segmented rings.



Re: built my Seg-easy the last 2 days *LINK*

#4

Re: built my Seg-easy the last 2 days

Gary clarke

I like my seg-easy, but haven't had time to master the angled cuts yet. Hard to find time because I am retired.πŸ˜€

Re: built my Seg-easy the last 2 days *LINK*

#5

Re: built my Seg-easy the last 2 days

doug williams

Gary I like your response, have watched that video a couple times and will have to tinker with that jig. Looks fun to build and thanks John.

Re: built my Seg-easy the last 2 days *LINK*

#6

ebd

Re: built my Seg-easy the last 2 days

ebd

I built & modified a different sled which took a lot of time to get perfect. It's now locked down to cut 12 segment rings perfectly. Had I seen this jig I would have done it this way. If I ever want to do a different number of segments I'll build one of these. It seems to take away all the agony of getting the angle perfect once you have a perfect template. (OUTDATED: Not sure where those come from other than buying from Seg-easy - except the 30 degree which gives 12 segments.) Just saw John's post. Got to get one of those angle vernier calipers.

On my sled I flip the stock to cut the next segment which at times (especially with lacewood) yields interesting grain change, segment to segment. To get the exact same grain showing I have to waste a bit between each segment cut. With this sled the reverse is true. Might build one just to have the no-flip option available.


Re: built my Seg-easy the last 2 days *LINK*

#7

Re: built my Seg-easy the last 2 days

John Lucas

Flipping the wood amplifies any inaccuracy Keith and I were discussing this the other day. When aligning a table saw blade or miter gauge for square it's cooking practice to make a cut and then flip the board and put them back together. This doubles any errors and lets you really dial in the blade

Years ago when I used to make a lot of picture frames. ( I am a photographer you know ) I found that if I made a 90 degree fence and cut the liters from bothe sides it gave a much more accurate joint So why it never occurred to me to do demented miter this way I don't k ow. I'm really thankful to Jerry Bennet for giving us this. It should improve my consistency and I might start doin more segmented work.

Re: built my Seg-easy the last 2 days *LINK*

#8

Re: built my Seg-easy the last 2 days

Rick Haverstock

John,

Is that vernier angle caliper a current HF offering? Was interested and when I checked their website I couldn't find it. Thanks !

Rick

Re: built my Seg-easy the last 2 days *LINK*

#9

ebd

Re: built my Seg-easy the last 2 days

ebd

Actually, if you keep them flipped and keep the segments in order the errors compensate and match perfectly. Also I use a Wixey to zero the arbor to the table. Any error is miniscule/negligable.

Any problem would only come in if you try to keep the same face by un-flipping the segments (every other one). Even then, using the Wixy I don't think the error would be a problem. The device is accurate to 0.1 degree. Over the thickness of even a 2" segment that's almost nothing. It might be significant machining metal, but not, I think, on wood.

Re: built my Seg-easy the last 2 days *LINK*

#10

Jim Evans

Re: Angle Caliper *LINK*

Jim Evans

This is the only one I could find, but it is 24" long.


Big Angle caliper

Re: built my Seg-easy the last 2 days *LINK*

#11

Re: Angle Caliper

Hugh Buttrum

John,

I am interested in the caliper in your second picture.

Any chance you can tell us where you got it? I too looked at the Harbor Freight web site and could not find it. Any help would be appreciated.

Thanks.

Hugh

Re: built my Seg-easy the last 2 days *LINK*

#12

ebd

Re: built my Seg-easy the last 2 days

ebd

We are talking about apples and oranges.

Re: built my Seg-easy the last 2 days *LINK*

#13

ebd

Re: built my Seg-easy the last 2 days

ebd

We are talking about apples and oranges. In other words, you are entirely correct, but that's not what I am talking about. Don't know how to describe it to you (I could show you if you were here). Bottom line is that my segments come out yeilding perfect joints even if the saw blade is off by a small or large amount. I get the blade to within .01 degrees of perfect simply because I can. I might tilt the blade 30 degrees or so off perpendicular just to see what the segment ring would look like once turned.