Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Highlighting chatter work

Posts

Highlighting chatter work

#1

Highlighting chatter work

David Walser

Gentlepersons, I could use your help. I'm working on a project that includes a couple narrow bands of chatter work that I would like to highlight by filling them with gold. In the deep recesses of my memory there is a product that can be rubbed on and then buffed off, leaving the gold colored material in the voids. I thought the product might be "Rub'n Buff". I don't think Rub'n Buff will do what I want. (It'll highlight the top surface of the pattern, not fill the voids.) Any suggestions (including where I can purchase this magical material)?

Re: Highlighting chatter work

#2

Re: Highlighting chatter work

John Lucas

Rub n buff will fill the voids you just have to use more of it. It's a paste. If you just use a little it will highlight the tops. If you use more it will fill in the gaps. I also use shoe polish for that purpose but shoe polish doesn't come in gold. Rub n buff comes in copper, silver and gold.

Re: Highlighting chatter work

#3

Re: Highlighting chatter work

David Walser

John -- Thank you for your reply. Perhaps I'm being a little dense, but I don't understand how I would use rub'n buff for what I want to do. Yes, I know I can get it into the low places, but how do I remove it from the high places (and the surrounding area)? Say I had engraved some text and wanted to just fill the letters with gold. Can I rub some rub'n buff into the letters and just wipe off the excess with a clean cloth? If so, I'm golden (so to speak). I could sand the excess off the high spots, but that would remove the black paint, too.

Re: Highlighting chatter work

#4

Bill Blasic

Re: Highlighting chatter work

Bill Blasic

David there is a gold colored (probably silver too) crayon type stick that will do what you are looking for. I know Cindy Drozda uses one for signing her pieces. Here is a link to something similar:

http://www.brownells.com/gunsmith-tools-supplies/general-gunsmith-tools/engraving-tools-supplies/inlay-color-fill-sticks/lacquer-stik-reg--prod7778.aspx

I have one but I don't remember where I got it from. Search "gold fill stick crayon"

Re: Highlighting chatter work

#5

Re: Highlighting chatter work

John Lucas

David there is the challenge. You can remove it with a cloth with a little mineral spirits. However, and this is the biggy. It is fine enough it will go into any pores or poorly sanded areas. What I usually do when I want this sort of effect is to sand really good before I do the chatter work or sign my name. Then I apply a thin coat of finish. This helps fill the pores of the wood but not the chatter work or signature. Apply the wax whether it is crayon, or a wax. Then apply just a drop of mineral spirits on a rag and stretch it over your finger tip. Now gently rub to remove the wax from the high points.

If your doing letters and they are carved fairly deep you can apply color and then sand the top surface lightly to remove the wax or in some cases I use spray paint. I will apply thinned finish and then spray on a light coat. then you can go back with fine grit paper like 220 or 400 and sand off the spray until just the carving is left.

If the carving is fairly deep you can even turn away a very thin layer or even shear scrape to leave the paint or wax in the grooves.

An alternative process that goes along with this is to then cover the high points. For example you might have one color in the chatter work grooves and another color on the high points of the chatter work. For selective areas such as chatter work on spinning tops I fill the low areas, sand lightly or use mineral spirits to remove it from the high points. Then use a colored permanent marker to highlight the high points. Another alternative for larger areas is an ink Brayer. You can roll on a thin layer of ink and it will only touch the high points. I believe I learned that from Clay Foster but don't remember for sure I've used it for so long.

Re: Highlighting chatter work

#6

Re: Highlighting chatter work

John Lucas

If you screw it up. Meaning that you rub the wax into the grooves or texture and find that some of it still gets into pores and other areas you don't want you can get it all back out with a tooth brush and mineral spirits and start over. Not that I've ever done that you understand. You can also sometimes take mineral spirits on a small artists paint brush and get the wax out of some pores.

Re: Highlighting chatter work

#7

Re: Highlighting chatter work

Dale Gillaspy

What John Said. A Tung Oil Blend will take it off the same as the mineral spirits. I usually seal the surrounding wood with some type of finish, then apply, then use the oil to wipe off.

Re: Highlighting chatter work

#8

Re: Highlighting chatter work

Don Evans

Here is a similar product you can check out see if it may do what you want.

Baroque Art Gilders Paste

It is similar to shoe paste wax and comes in many different colors.

I get mine via Amazon, they don't stock it so it is really coming via another store if you order thru them.

Could just do a Norton Safe search (I don't like google but you can use them also) and go to one of the places that sell it and read about it.

It works very good.

On your particular venture with what you are doing on chatter, it appears to me that the applicator you use is more important than anything. Would a small artist type paint brush with any of these waxes or paste get down into the crevices. If it will then I would turn the object in the reverse direction to remove the paste from the top parts, doing it that way should keep it in the low areas undisturbed if you use a light touch.

Don

Re: Highlighting chatter work

#9

Thanks, everyone

David Walser

I really appreciate the advice. It's been a great help.

Re: Highlighting chatter work

#10

This is what I wanted *LINK*

David Walser

In the linked YouTube video, Cindy Drozda demonstrates how she fills with gold her engraved signature on one of her turned pieces. She uses a product called Lacquer-Stick from Markal. After filling the engraving, she uses a paper towel to wipe the surface clean of the excess gold filling. Then, she finishes the clean up with a light touch of 4,000 grit jeweler's paper.

Pretty neat.


Drozda video

Re: Highlighting chatter work

#11

Re: This is what I wanted *LINK*

John Lucas

You can get lacquer sticks in a wide variety of colors. I still have a whole set left over from my camera repair days. I don't have gold though. They were easy to find on Amazon.


http://www.amazon.com/Laco-Markal-Lacquer-Stik-Paintstick-Gold/dp/B005KLD146/ref=sr_1_1?ie=UTF8&qid=1419442925&sr=8-1&keywords=gold+lacquer+sticks

Re: Highlighting chatter work

#13

Bill Blasic

Re: This is what I wanted

Bill Blasic

No Bill that doesn't work well for the signing thing. The Markal sticks are in line with what I was talking about.