Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Using Epoxy In The Cold

Posts

Using Epoxy In The Cold

#1

Using Epoxy In The Cold

Stuart Johnson

Will two part 5 minute epoxy mix and set up properly in the cold. In this weather it's hard to get the shop over 50 degrees and the piece I'm working on is a Christmas present so it's either the shop or very late at night if I want to do it in the house.

Re: Using Epoxy In The Cold

#2

Re: Using Epoxy In The Cold

Chuck Engstrom

Hi Stuart -- Most likely it will be just fine, though it will take a good bit more than five minutes to set up. Some epoxy suppliers specify suggested minimum temperatures but if you are patient you'll probably get a satisfactory result no matter what.

A couple of suggestions -- mix a small batch and just let it sit to see how it performs. Even five-minute epoxies take generally longer than that to fully cure even in summer, so a slow result should not be surprising. And if you can take your work into a warmer spot after you've applied the epoxy, you'll speed it up substantially.

Good luck with it -- Chuck

Re: Using Epoxy In The Cold

#3

Re: Using Epoxy In The Cold

Keith Newton

I don't use 5 minute, but I've used a lot of epoxy in a cold shop. While I'm mixing, I hold the solo cup tilted under the hot water as it comes out of the faucet. It needs to get warm at this stage.

Then after it goes on the wood and after assembly, I use a tarp with little space heater blowing under the tent for larger projects. But for something small, I will bring it into the office, or bathroom overnight.

Re: Using Epoxy In The Cold

#4

Re: Using Epoxy In The Cold

Mark Mandell - Gone Round In New Jersey

You can warm the wood with a blow-drier or heat gun just before applying the mixed resin. That will speed up the initial gelling. A couple of halogen spots will keep things perking along as well. If, however, you're pouring a thicker/larger section of resin, a cold shop will assist as it will slow the reaction and thus lessen the heat produced that can tend to deform, even fracture, the resin "block."

Re: Using Epoxy In The Cold

#5

Re: Using Epoxy In The Cold

John Lucas

Do a test before putting on your final project. It probably will but I would just mix up a dab and put on something that you can poke later. After you think it's dry stab at it and scrape it to see how strong it is and if it's hardened properly.

Re: Using Epoxy In The Cold

#6

Re: more likely to get amine blush on surface

Rum

probably won't matter for your use case though.

Re: Using Epoxy In The Cold

#7

Re: Using Epoxy In The Cold

Stuart Johnson

Thanks, I'll mix up a bit and see what it does. I should have been more specific. All I'm doing is adding a handle and medallion to a mirror and sticking a pig tail flipper into a handle.

Re: Using Epoxy In The Cold

#8

Re: Using Epoxy In The Cold

Bill Jacksonville, NC

Have used many different brands of epoxy and actual set up time can be anywhere from forty five minutes, one hour, or two. Regardless of time on the packaging always wait a day before use.

Also if do not mix same amounts of hardener to resin or not mixed long enough will delay set up times.

While they do make a cold weather epoxy most brands are good down to 35-40 degrees, of course cooler weather can and does affect set up and for use times. Depending upon brand can take more than couple days to fully cure.

Re: Using Epoxy In The Cold

#9

Brad Vietje

Re: Using Epoxy In The Cold

Brad Vietje

West System performs pretty well in the cold -- but as you'd expect, the cure times are longer. Probably good to keep in mind that exposing a cold fluid to warmer air could lead to moisture condensing out of the air, and affecting the mix. If the goop is hygroscopic, or catalyzed by moisture (like CA) it could have a negative effect.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Using Epoxy In The Cold

#10

Re: Using Epoxy In The Cold

Terry

A trick I used to use when I lived in Illinois was to take a pan of very hot water and put the epoxy in a zip lock bag and let it sit for 10 or 15 minutes. At that point it flows very well, you can mix and apply it and it will dry just fine.

Good luck