Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Black Acacia questions

Posts

Black Acacia questions

#1

Black Acacia questions

Jeff Smith

Just returned to Seattle from Thanksgiving trip to Santa Cruz / Monterey Bay Area of CA with a good sized chunk of Black Acacia a furniture maker friend sent me home with. He's got the rest of the tree sitting behind his shop. Saw some pieces he's built with it and it looks stunning milled as lumber.

The picture shows a single round that started at 36" diameter x 40" in length. I cut it into two slabs 36" x 36" and saved the outside slabs at roughly 20" x 24" along a few larger pieces stuffed into the back of our SUV.

I'm not familiar with turning acacia - it's pretty wet - been down about 4 or 5 weeks at most. Does it move a lot? Split? Heavy - like locust, but better color with lots of variation.

Any of you California turners familiar with turning it? I understand that it's a relative of Koa - does it turn about the same?

Re: Black Acacia questions

#2

Re: Black Acacia questions

john Veerkamp

Not from California, but I have turned some much smaller acacia from Texas. Fairly hard but prone to split. Your outside slabe may not have this problem. It turned beautifully with some stunning color variations.

Re: Black Acacia questions

#3

Re: Black Acacia questions

David Staeheli

I've turned some from Santa Barbara area. Had more luck with leaving whole to dry than rough turning to dry. Got lots of rough turned blanks with numerous splits. But the ones I dried for several years as end sealed blocks I got bowls out of. Well worth waiting for!

Re: Black Acacia questions

#4

Re: Black Acacia questions

Hugh Buttrum

Great stuff, Black Acacia is. Turns really well when wet. It moves, but usually not that badly. I would rough out bowls or whatever and seal with Anchor Seal. Mark the date and then stick it back on the lathe in a year or so. It does contain silica I think as it will dull your tool. Just re-sharpen. People love it's color and grain. Has nice contrasting light sap wood. You can turn hollow forms to finish and yes they do move, but if you dry them slowly, they will come out. If you keep in chunks - make sure you seal the end grain. But drying like that can take a long time and end up with cracks.

I have had pretty good luck with Black Acacia.......but then there is the bowl that I roughed out, sealed up.....let dry a year and put it back on the lathe to re-turn it. I trimmed off the out side and stopped for lunch. Came back and there were two large cracks. But you are bound to loose some ....some of the time.

Considered a weed in California. They would love to get rid of it. I turn it when I can get it.

Hugh

Re: Black Acacia questions

#5

Brad Vietje

Re: Black Acacia questions (Caution: RANT)

Brad Vietje

OK, Time for me to be a real jerk as well as a real PITA (I hope people can forgive me for making an example of this particular case):

Let me try to sort this out.... you just loaded about 400# of wet, green wood in your car and transported it some 1000 miles to an area where this tree is not native, right? Transporting any beetles, their larvae, eggs, and possibly thousands of little infectious creatures a thousand miles to help them spread across the country in days, instead of decades ? I'm sure that was not your intent, but it could actually be the result.

Sorry to be such a wet blanket -- truly, I am not an a**hole, but we woodturners have to start thinking about this stuff, or we will wipe out the forests that are the supply of all the wood we love to work with!

Now, I'm a biologist by training (but no longer work in that field), and I know well that not every species of wood/tree is currently at risk, but the list of tree infestations is growing at an incredible rate. If we wait until a specific species is identified with an infestation problem, IT WILL BE TOO LATE -- the damage will have been done. In other words, when we ship or transport green wood around the country, we are playing Russian Roulette with the trees we love so much.

Just reflect for a moment on American Chestnut, American Elm, the Emerald Ash Borer, the Hemlock Wooly Adelgid, Asian Long Horned Beetle, Pear Thrips, etc, etc, etc... When you add our actions to the stresses of Climate Change, these trees are under some serious stress, and they just can't respond quickly enough to survive.

So -- the woodturner in me says "Great Haul -- Nice Looking Wood !", the biologist in me says "Jeff, you should know better". We simply need to stop doing this.

Would you please at least place these chunks in sealed plastic bags until you get to turn them, and perhaps burn the shavings? I think that would go a long way to stopping any potential spread of disease. If you see any insect damage in your rough-turned items, I hope you will consider boiling, microwaving, or kiln-drying them to make sure the little critters are killed.

Off my soap box now -- sorry to come down so hard on you -- I could have picked on anyone moving green wood about, so you are just the victim of timing. But seriously, folks, we need to start taking this stuff, um, seriously.

Safe spinning, and -- believe it or not -- warm regards,

Brad Vietje

Newbury, VT

Re: Black Acacia questions

#6

Re: Brad keep preaching & RANTING


Re: Black Acacia questions

#7

Re: Black Acacia questions (Caution: RANT)

Barry L Elder

Brad, methinks you are preaching to the choir! While most turners (in the States under quarantine) are sure to pay attention, newbies and others just don't have the good sense to protect the future for anyone but themselves. " I done ain't never seen nuthin' like that" was a comment from one guy at a woodturner meeting recently. Yes. it's sad!

Re: Black Acacia questions

#8

Re: Black Acacia questions (Caution: RANT)

Hugh Buttrum

I will ask this question again as I never received a response earlier:

What about the burl sellers? They are shipping it world wide. They take out whole orchards and haul it to another part of the state and then ship it out to ? In the north part of California, ranchers are allowing woodcutters to come in and take out 90+% of the Blue Oaks on the property and hauling it to the big city for firewood. The market up the street sells boxes of "hardwood" for $8 a cubic ft. of firewood. They hauled if from ?

I am not saying it is right to transport wood......but look at the various wood sellers around. They are bringing in wood from all over.

Hugh

Re: Black Acacia questions

#9

Re: Black Acacia questions (Caution: RANT)

Jeff Smith

Brad - I do appreciate the rant. In fact, I did not consider the possibilities, but I do know how the wood has been handled. This wood was a gift from a long-time friend who has been building custom furniture for well over 30 years. He mills most of his own lumber, most supplied by local professional arborists. I'm pretty sure they'd advise him of any potential for transferring infestations if it was a possibility.

Before milling and while they're in his storage area, he pressure washes the raw log sections with a mixture of insecticidal soap (check the well-thinned bark sections on the pieces). With several slabbed trees in his drying yard at any time, he's careful about introducing anything into the drying stacks. We had to cover the load with canvas for the two day trip home - my wife's sensitive to most smells...

I'll be boiling the roughouts - just my normal SOP, and the bark is always removed before turning to keep it from launching - I'll take your advice and burn it. Shavings always go to composters.

Re: Black Acacia questions

#10

keep saying it, Brad; it needs to be said


Re: Black Acacia questions

#11

Re: Black Acacia questions (NON RANT)

jim breeden

For those who have never turned acacia / mesquite, get ready for a tremendous amount of dust - no matter green or dry, turning or sanding. Get you DC tuned up, put on your heavy duty dust mask, and your face shield. The chips coming off this stuff is like being hit with bird shot.

Re: Black Acacia questions

#12

Brad Vietje

Re: Black Acacia questions

Brad Vietje

Hey Jeff,

Thanks for being aware of the issues, and for taking measures to stop the spread of tree diseases. If everyone else did the same, we wouldn't have such a severe problem.

BTW: Great haul of really beautiful wood! 8)

Safe spinning,

Brad Vietje

Newbury, VT