Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

square headstock in the way

Posts

square headstock in the way

#1

square headstock in the way

John Lucas

Obviously I turn different that many others. I hear complaints about the Powermatic square headstock geting in the way. I've had mine for about 12 years now and the only times it's been a problem I think any headstock would have been a problem.

Can you all describe what cuts you do where the headstock is in the way. Just trying to learn what I'm doing wrong. :) Seriously, I'm sure you have logical reasons it just doesn't happen with my style of turning and what I turn I guess.

Re: square headstock in the way

#2

Ric Taylor

Re: square headstock in the way

Ric Taylor

Whenever I need more room on the headstock side of my piece I use an extension on the chuck, between the chuck and the headstock. It gives me about an extra 6 or 7 inches of room between the chuck and the headstock, with zero runout.

Ric

Re: square headstock in the way

#3

Re: square headstock in the way

Sergio

Any time I need to do fine cuts close to the chuck. I too have a spindle extender but often my left shoulder need to be close to the lathe. Another example is to clean a bead on a bowl or other turning, near the chuck. To run the spindle with the grain one has to go from chuck to rim. I always prefer a pysh cut to a pealing cut and often use a spindle gouge to finish the surface close to the tenon.

Also that bulky headstock is often interfering with the tool handle in those cuts. This at least in my experience.

I just went to the lathe and working on a small bowl it came to my mind that another problem I had were the legs interfering with my feet. The VL3000 is completely flat. Nothing to bother your feet while you are dancing with it.

Re: square headstock in the way

#4

Re: square headstock in the way

robo hippy

My 3520A had a groove in the headstock to allow for getting closer to the bottom of a bowl where you are twice turning, have returned the tenon, and reversed it for final finish cuts. Since I turn green to final thickness, never an access problem for me as the outside is finished turned before I reverse it. I have tried a few, and some times the 70 degree bevel gouges can get in there where a 45 degree bevel won't. Also, a dropped handle, high shear angle cut can work till you get far enough away for better access.

robo hippy

Re: square headstock in the way

#5

Re: square headstock in the way

John Lucas

I turn the bowls around to finalize the foot This way I can use a spindle gouge sharpened at a 35 degree angle and do a push cut against the grain. Usually I clean it up and shape the foot using pull cuts with the bowl reversed. Then clean up that last 3/8 with the spindle gouge

I normally do a push cut working from rim to foot or close to the chuck depending on the shape. The. Reverse the bowl and finish the bottom. This keeps the headstock from being a problem

Re: square headstock in the way

#6

Re: square headstock in the way

Sergio

There are nine ways to skin a cat. The important is the result. The best situation in any case is a lathe that allows all the positions as easy as possible. Oneway, Robust and Vicmarc are one step above in my opinion.

PS: Poor cat of course.

Re: square headstock in the way

#7

Re: square headstock in the way

RCH

Usually I don't have trouble with the Jet 1642 or Powermatic headstock getting in the way. However, when I work on some bowls or plates with complex toward the center, I have to work alternately on one face then the other to get the thickness and profiles right; there can be several dozen such alternations. Sooner or later the headstock gets in the way. Given that, remounting repeatedly would get old, waste a lot of time, and re-centering accurately could get problematic.

Re: square headstock in the way

#8

Brad Vietje

Legs: Yes.  Headstock: No.

Brad Vietje

I never seem to have that trouble, either. I start and finish very nearly every bowl between centers, so I have no real access problem from the headstock. The older 3520A models were rectangular, but my 3520B has a beveled headstock. I sometimes work with my left shoulder leaning against that bevel, so I'm glad it's there. I've turned on OneWay lathes many times, and never found the round headstock any advantage -- maybe I've learned to work around the clunkier PM, so I just don't have the same issues a OneWay turner would have on my lathe (?)

The tailstock gets in my way sometimes, a heck of a lot more often than the headstock. Maybe I need a vacuum chuck?

Safe spinning,

Brad Vietje

Newbury, VT

Re: square headstock in the way

#9

Re: Legs: Yes.  Headstock: No.

Sergio

A vacuum chuck? Since I got one (actually three From Oneway) my turning life has changed. The only problem I have with them is that with soft wood, butternut for example, even at a not too strong vacuum, the chuck leaves a compression sign similar to a burnishing mark.

Re: square headstock in the way

#10

Love my vacuum chuck.

John Lucas

I've made my vacuum chucks. I am always playing sealing materials The soft ones seal better especially on mildly warped bows but they throw them off center. Not a problem if you reshape the entire foot If the foot is already done then you can't touch it. On those I just clean up the very bottom

The stiffer gaskets aren't fore giving of warp but align better. They are also more likely to leave a burnish mark

Re: square headstock in the way

#11

Re: square headstock in the way

John Lucas

I do like the square headstock top on my lathe. I am constantly putting small things up there I put my magnetic light up there and the magnet will hold small wrenches a d index pins etc