Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

hollowing dried dogwood

Posts

hollowing dried dogwood

#1

hollowing dried dogwood

John Lucas

Man I was hollowing some dried dogwood limbs for christmas ornaments yesterday while waiting for the paint to dry on the molding and cabinet I'm doing for my bathroom redo. That stuff is hard. I can usually hollow most ornaments in just a minute or two without sharpening my tools (which are homemade High carbon steel that's been hardened). I had to stop and sharpen at least 3 times and could only take small bites.

What I thought would be a 15 or 20 minute job took an hour. I knocked one of the blanks off when the CA glue sheared. Fortunately I got it glued back on with less than 1/16" out and since the outside was done I just thinned out the inside some more and called it done.

gotta do a lot of work on the bathroom before I leave for Thanksgiving so may not get the finials done until the weekend but I'll post photos.

I thought it would be fun to try and dry some dogwood limb sections for things like boxes and ornaments. It worked. Dipped the ends in wax and put them on the shelf. ONly had small checks in the very ends. Not sure how long they sat. Probably a year or so but can't really remember when I cut them.

Re: hollowing dried dogwood

#2

Ken Vaughan

Re: hollowing dried dogwood

ken vaughan

Dogwood was a commercial species once upon a time -- it was sought after for shuttles for the weaving trade.

Lee Valley had a close out of a stock of well dried dogwood some years back. It is more akin to boxwood when cured dry. Holds exceptional detail.

The weaver I live with has an old dogwood shuttle that she got 2nd hand and has used for years. Hardly any wear. Much better than hard maple for holding edges and details.

Re: hollowing dried dogwood

#3

ebd

Re: hollowing dried dogwood

ebd

I found lilac to be very hard (like ivory) but no where near as hard as what you are describing.

Re: hollowing dried dogwood

#4

Re: hollowing dried dogwood

Rum

The obvious follow up question is does it finish up pretty enough to justify the effort?

Interesting info on its uses and wear capability. Might have to get some to make more shuttles for loml, the rest I've made were various other scrap hardwoods :) They don't take long to make and at the low use they get here.. not a problem. There are some other higher wear items where something like that could be real handy though (and getting good quality bone to work has been proving difficult to find).

Personally I love lilac if I can get it, it has a very fine grain so you can cut it any which direction and it's still pretty strong. Makes gorgeous shawl pins, thimbles, finely carved spoons, etc... It's hard to find a piece big enough to use for much though and tends to twist and spilt badly while drying which limits the usable wood some (stable one dried though). I have a 5" log in the stash that's been dying for four or give years now (old tree got washed out of a creek bank and had to be removed). They also used to coppice out to get stat staves as a premium bow wood.

Re: hollowing dried dogwood

#5

George Balock

Re: hollowing dried dogwood

George Balock

Rum.

Be very cautious using lilac for food contact. It has some toxicity issues.

I've found dogwood to be an excellent species for boxes also. It's hard as a rock and holds details marvelously.

Re: hollowing dried dogwood

#6

Re: lilac toxicity source?

Rum

I can't find any references to lilac wood being toxic and quite a few to it not being toxic, the seeds possibly yes but not the wood (or flowers).

This is for true Syringa vulgaris and close Syringa Genus relatives (http://en.wikipedia.org/wiki/Syringa), not some of the other woods/shrubs with "lilac" in the name like Chinaberry (aka persian, indian, cape lilac - looks it up - Melia Azedarach http://en.wikipedia.org/wiki/Melia_azedarach) which is a whole different beast. Confusingly the poisonous one also sometimes known as "syringa berries" or "syringa tree" even though its not a Syringa. Knowing the difference would be important :D

Re: hollowing dried dogwood

#7

George Balock

Re: lilac toxicity source?

George Balock

Rum,

Unfortunately, I don't have a reference. It was something I read years ago about some of Napoleon's men using lilac branches to roast meat over a fire. But, on your response, I searched the Internet and came up with the same information as you did--non-toxic. It wouldn't be the first time I was wrong, just ask my lovely wife!

Re: hollowing dried dogwood

#8

Re: hollowing dried dogwood

Mark Mandell - Gone Round In New Jersey

I highly recommend dogwood, both wet (absolute fav) or dry. Hollowing can be a challenge, however. For that I recommend that your Hunter tools come out of the rack.



Re: hollowing dried dogwood

#9

PS:  Finish

Mark Mandell - Gone Round In New Jersey

Krylon Matte Finish will then burnish up nicely with 4-0 wool. It needs nothing more.

Re: hollowing dried dogwood

#10

Re: lilac toxicity source?

Rum

No problem, there are plenty of woods out there that you shouldn't touch so cautious is better than sorry! I'd rather not use something than find out the hard way I shouldn't have.

Snopes claims that the poisoning was Oleander (and also found some references that it happened to Alexander the Great so its probably apocryphal although certainly plausible it happened to some soldiers somewhere sometime).

Given how poisonous Oleander is I certainly wouldn't want to try to recreate the event anyway :D

reference

------------

snopes.com/horrors/poison/oleander.asp

In 1809, when the French troops were lying before Madrid, some of the soldiers went a marauding, every one bringing back such provisions as could be found. One soldier formed the unfortunate idea of cutting the branches of the Oleander for spits and skewers for the meat when roasting. This tree, it may be observed, is very common in Spain, where it attains considerable dimensions. The wood having been stripped of its bark, and brought in contact with the meat, was productive of most direful consequences, for of twelve soldiers who ate of the roast seven died, and the other five were dangerously ill.

--------------

Mark, that is an absolutely awesome box! Great design and execution.

Re: hollowing dried dogwood

#11

Back in the wood for golf driver.......

JamieDonaldson

....head days, when "woods" were really made of woods, dogwood was among the desirable woods for such applications.

Re: hollowing dried dogwood

#12

Re: Back in the wood for golf driver.......

Emmett Manley, Lakeland, TN

Yes, dogwood and persimmon were the main two trees used to make golf "woods," along with laminated material. Both dogwood and persimmon are spectacular turning woods; hard, hold detail, and polish like glass. Persimmon was used far more than dogwood because it is more plentiful, larger (10" diameter required for a driver), and far fewer problems with cracking. Dogwood, like cherry, wants to crack and will break a woodturner's heart.