Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Which D-Way CBN

Posts

Which D-Way CBN

#1

Which D-Way CBN

Stuart Johnson

What is the preference in CBN wheels 80 or 180 grit? I plan on keeping one matrix wheel and just purchasing one of the CBN. On D-Way's site the one video says he doesn't see any difference between the edges when on the lathe.

Also is there an advantage with the 1-1/2 wheel vs. 1 inch wheeL?

Re: Which D-Way CBN

#2

Re: Which D-Way CBN

Curt Stivison

I have recently bought a D-Way 180 grit CBN wheel. It does an excellent job but in my opinion if you want make a change to the profile of the tool very much you need to have the 80 grit wheel. Both grits do an excellent job.

Curt

Re: Which D-Way CBN

#3

Re: Which D-Way CBN

robo hippy

Well, I have both. As for wheel width, get the 1 1/2 inch wide wheel. Main reason for me is that since I got the wide wheels, I have never 'slipped' off the edge when sharpening gouges. It used to be a fairly regular occurence, jigs or free hand, with the 1 inch wide wheels. I keep going back and forth with my scrapers and fluteless gouges to see which wheel leaves the best burr. I am thinking I prefer the 80 grit wheel for the scrapers, because it is heavier and better suited for heavy roughing. Some times I like the 180 grit for the fluteless gouges because it is a bit finer for a better finish cut. I keep changing my mind about that though. Then, there is radius or square edged wheel. I have a set of the radius wheels, but haven't used them. The main advantage of them that i can see is if you sharpen a lot of hollowing bits in the jigs. It is easier to push it straight through the radius part than it is to pivot it around.

robo hippy

Re: Which D-Way CBN

#4

Re: Which D-Way CBN

Phillip Medghalchi

Stuart, I hope you haven't ordered it yet. I bought mine from this guy for half that price so for the price of one CBN wheel form D-Way I bought two form this vendor. I post his name and the phone number in just a min. so you can take a look at it.

Re: Which D-Way CBN

#5

Ken Vaughan

CMN Wheels -  Ken Rizza???


Re: Which D-Way CBN

#6

Re: CMN Wheels -  Ken Rizza???

Phillip Medghalchi

Ken, I think that' the one for $124.95, and I got the 80 grit and 180 grit. He cam up with a new one that wraps around the wheel for side grinding also.

Stuart you have to make sure that your spindle ont eh grinder is long enough for the wheel to sit against the shoulder to run true.

I have the Rikon and it was too long. i had a machinist frind of mine to make bushing to go on the spindle to make it both run true and sick out where it's supposed to go. It may sit too far back form the last thread on your grinder shaft that makes it wobble. So, yo have to fill that gap with a bushing he aslo sells those if you tell him what you got. I check for you after the dinner to make sure that's the one.

Re: Which D-Way CBN

#7

Re: Which D-Way CBN

Jeff Smith

I've been using D-Way CBN wheels for a couple of years now - both the 80 and 180 grit. As has been mentioned, I use the 80 mainly for scrapers or for heavy reshaping. Don't know that I can tell the different between the burr from the 180 and the 80, but I've got my Robo Rest platform setup on the 80 grit side most of the time.

All D-Way wheels are 1-1/2" wide - even the radiused edge versions. Mine are the earlier square edged version - I'd like to have the radiused edge for hollowing tools. If these ever wear out (I doubt that's going to happen in my lifetime), I'll get the radiused edge for the 180.

Dave's recently added 7" and 10" sizes of the standard, square edged wheels - the 7" is for Baldor 7" grinders and the 10" works on Tormeks.

Re: Which D-Way CBN

#8

Re: Which D-Way CBN

Steve Worcester.

If you have a higher grit already and can only afford one, get an 80 grit. Reshaping or even as an only wheel the CBN is better than an aluminum oxide or blue or red wheel. Less dust and no need to true it.

If you can afford both, get the 80 and 180 wheels. You won't have any buyers remorse.

As for width, if the grinder can take a 1.5" wheel, and you use a Oneway or SharpFast jig, the tools has more room to move around resulting in less of the tool sliding over the edge.