Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Speed Controller for Delta 1220 Lathe Problem

Posts

Speed Controller for Delta 1220 Lathe Problem

#1

Speed Controller for Delta 1220 Lathe Problem

Peter Toch

A friend of mine asked me to take a look at his Delta 1220 Midi Lathe (Delta Model #46-460 VS) which has a variable speed controller which has stopped working and to see if I could repair it for him. I disconnected the motor from the speed controller and it ran fine when connected it another variable DC speed controller I have. Conclusion, motor good, speed controller bad. Delta Parts has been less than helpful and claim that a replacement controller circuit board is no longer available. Inspection of the defunct controller does not show any obvious signs of damage such as burned areas or components or any classic "electrical burnt odor."

Questions:

Has anyone run into this or a similar problem with this lathe?

Were you able to find a solution to replacing or repairing the circuit board?

Does anyone know of someone that can analyze and repair the board?

Does anyone know which of the components on the board are the most suspect?

Any suggestions are most appreciated. Thanks, Peter Toch

Re: Speed Controller for Delta 1220 Lathe Problem

#2

Re: Speed Controller for Delta 1220 Lathe Problem

Chuck Engstrom

Hello Peter -- It could be that the best bet here is to find another DC controller to power it, as you did in your testing. I'm inclined to suspect -- this is just conjecture -- that the Delta part is no longer available because so many of the originals have failed that all the spares are already gone out. I have a Delta drill press with a "no longer available" crucial part and suspect the same issue in that case.

Google for "dc motor speed controller" and you'll find plenty of choices, including some kits. Friend may end up with a cobbled-together arrangement that's less pretty than the original but it would get him back to work.

Good luck with it! -- Chuck

Re: Speed Controller for Delta 1220 Lathe Problem

#3

Re: Speed Controller for Delta 1220 Lathe Problem

stan townsend

I had a similar problem and it turned out to be a loose wire in the power cord to the wall plug. One leg without power will stop the controller dead.

Re: Speed Controller for Delta 1220 Lathe Problem

#4

Re: Speed Controller for Delta 1220 Lathe Problem

John Lucas

Check for loose wires and cold solder joints. A bad solder joint will often look dull rather than shiny. Also some will have fuses, so look for those. So far I've failed miserably to be able to repair any DC controllers on my own. Just don't have the electronic skills or tools to trouble shoot down to the component level. Ok Not completely failed. I have repaired a few for friends that were very simple repairs, loose or broken wires, or bad fuse, but nothing beyond that.

Re: Speed Controller for Delta 1220 Lathe Problem

#5

Ken Vaughan

Re: Speed Controller for Delta 1220 Lathe Problem

Ken Vaughan

Not that lathe but

Have had switch failures a couple of times -- easy to check with the volt - ohm meter.

Other piece that gets wear and tear is the variable resister (pot abrev) that is commonly used. Depending on the controller, that is sometimes an easy change out - and sometimes is imbedded in the IC board and beyond my skills and pay grade.

Re: Speed Controller for Delta 1220 Lathe Problem

#6

Re: Speed Controller for Delta 1220 Lathe Problem

Dick Coers

Did you check the reversing switch? Those go bad as well. I've also read that the potentiometer goes bad on the board. I sure hope some electrical guru comes up with a DIY fix, or a ton of us will have small boat anchors in the near future!

Re: Speed Controller for Delta 1220 Lathe Problem

#7

Re: Speed Controller for Delta 1220 Lathe Problem

john Veerkamp

If this is a Baldor controller , look for an authorized baldor repair shop in your area and have it fixed. My Delta 16" controller died. Took it to a shop and they had it diagnosed and fixed in two hoiurs. Turned out to be a bad solder joint. Cost me about $80. Much cheaper than a new circuit board or controller. This was after I took the head to a Delta repair place and they could only suggest buying a new controller for $600.

Re: Speed Controller for Delta 1220 Lathe Problem

#8

Re: Speed Controller for Delta 1220 Lathe Problem

Mike Brazeau

The controller board may not be available, but they can supply a whole new controller. With help from the local Delta Manufacturers Rep, he got the Sales Manager from Chicago involved on one of our guild lathes last year and they shipped a whole controller. Lately with the repair, sometimes It has been acting like it is dead, but if you just touch the hand wheel it starts. A crying shame the way Delta is being managed these days. This is a beautiful small lathe when it is working.

Re: Speed Controller for Delta 1220 Lathe Problem

#9

How much for the controller?


Re: Speed Controller for Delta 1220 Lathe Problem

#10

Re: Speed Controller for Delta 1220 Lathe Problem

Phillip Medghalchi

Peter, my local black & Decker (DeWalt, Delta) authorized rapir shop told me that the reason you can not get parts is that Delta sold their parts department to a Chinese company and for my friend's table saw it took them 5 month to get switch for the on-off.

That may be the problem you are dealing with. Those lathes if I am not wrong are not that old. Hoping, if it is still under warranty Delta should replace it with a new one. If you were in my town, there is an electric motor repair shop very old in down town who is very good and he repairs all the pro's tools, he could help you to figure out the problem. You may have to look up one in your area.

Good luck, and hope you do not have to spend $600 on a replacement.

Re: Speed Controller for Delta 1220 Lathe Problem

#11

Re: Speed Controller for Delta 1220 Lathe Problem

Janice Manuel

I had the same problem with my DL40 lathe last year..NO parts available from Delta...Ended up having a local industrial repair person make me a whole new speed control unit...I actually like what he made better than the original controler on that lathe...

Re: Speed Controller for Delta 1220 Lathe Problem

#12

Re: How much for the controller?

Mike Brazeau

Our unit was still under the five year warranty, so I don't know. I can look up the part number if you want to inquire with Delta.