Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Need assistance with rosettes

Posts

Need assistance with rosettes

#1

Need assistance with rosettes

AZ in Colorado Springs

I'm trying to make some rosettes out of maple. The wood is 1-1/4" thick, & 5" square. It's plain stock, not figured. I want to cut several concentric rings about 1/4" deep, starting 7/16" from the center, then every 7/16", for a total of four rings.

(One can buy rosettes, but they're about 3" square. Alternatively, one can get a bit for a drill press, but they seem to top out about the same diameter, maybe at 2-7/8". I want to make something a bit wider since this trim will be placed along the edge of a loft, about 11' high. I'm making fluted trim to go along with the rosettes.)

I have a piece of plywood mounted to a face plate, and screw through the back of the plywood, into the back of the work piece. The work piece is securely mounted.

I've tried using a narrow bowl gouge and a narrow spindle gouge to simply cut the circles, but I keep getting catches, which tears up the work piece. Suggestions?

My lathe is a Rikon 70-050VS, midi lathe.

Thanks

Andy

Re: Need assistance with rosettes

#2

Re: Need assistance with rosettes

John Lucas

Are you talking about beads or coves. I'm not sure what you mean by rings.

Re: Need assistance with rosettes

#3

Re: Need assistance with rosettes *LINK*

John Lucas

unfortunately I don't have a video yet on how to turn beads on a platter or side grain oriented piece. I do that all the time on my hand mirrors. The trick I use is to raise the tool rest way above center. I raise it about an inch for a bead that is about 2" from the center. This allows me to turn the bead exactly like I would turn it on a spindle. The video I provide here shows how I do that about 2minutes 17 seconds in.

It is much more difficult to turn if you have the tool rest on the normal center line. I think I show how to turn them using the 3 point tool and the skew on it's side. either of those methods is easier than the detail gouge but they don't leave as clean of a surface so much more sanding is needed.


https://www.youtube.com/watch?v=bjYehUsMdB4

Re: Need assistance with rosettes

#4

Re: Need assistance with rosettes

Dick Coers

I don't know how much instruction to give you. Do you turn bowls, or are you new with the use of bowl gouge? How is the bowl gouge ground? You could also use a Hunter tool with the right size cutter, turned on it's side while riding the bevel. If using hard maple, a freshly sharpened conventional scraper will do a pretty good job as well.

Re: Need assistance with rosettes

#5

Re: Need assistance with rosettes

AZ in Colorado Springs

OK, I have not had this on ignore, but the past several days got really crowded with activities. My turning experience: novice; I've done several sets of table and kitchen island legs and some other spindle-type stuff, and several bowls.

Am I after coves or beads? Beads, set pretty close to each other. What I did was to make a series of coves using the spindle gouge on one and the bowl gouge on the other (these are the "rings" I mentioned). Then I used the point of the skew to deepen the cut and shape the sides a bit. This turns them into beads.

But I'm getting catches which make unsightly gouges too deep to sand out.

I had the tool rest at the level of the center of the stock, or a bit below center. I saw the suggestion to raise it up a bit. I'll try that.

This seemed pretty simple when I began ... and that's not the first time I had that experience. javascript:insertTags(">(");

Re: Need assistance with rosettes

#6

I'm gonna make a video

John Lucas

I haven't done one in a while but will try to make one tomorrow showing several ways to make beads on a rosette. I may put some coves in it as well.