Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

gluejoints

Posts

gluejoints

#1

gluejoints

John Zeitner

Hello,

I'm trying to "sandwich" plexiglass and wood. I used epoxy (west-system), but it seems that the gluejoint cant take the heat and the Torque from the turning tool and the drill (for hollowing).

Does anyone have an idea what kind of glues might do the job? should I sand the epoxy before gluing to roughen up the surface a bit?

Thanks for any input

John

Re: gluejoints

#2

Re: gluejoints

John Lucas

Never had a joint failure with west system due to heat. I'd you tools are getting that hot something may be wrong. Of course dry maple and cherry can get pretty hot.

I suspect its the slick nature of plexiglass. I scratch it or sand it to give it some tooth for the epoxy to grab. The biggest problem with adding things like plastic or metal to turnings is wood movement. The plastics don't move and wood does I did a test one time where I glued an aluminum strip in a hand mirror blank a d the. Turned it. I placed it in my basement where it was cool and moist figuring the wood would swell and the metal shrink. Then i placed it in my car in the summer figuring the wood would shrink and the metal would expand. It held perfectly or so I thought. About 6 months later it just fell apart

Re: gluejoints

#3

Ric Taylor

Re: gluejoints

Ric Taylor

John,

This sounds like a project that you should take on with the "hope" that it will be successful, and don't be too surprised if it doesn't work out. As John Lucas said, it might just fall apart.

I recently did something along these lines knowing that it would probably fail, but I did it anyway. I wanted to sandwich sheet aluminum between pieces of wood.

I talked to a bunch of segmenters, looking for the adhesive that would would most likely be successful. After considering all of the advice and doing a bunch of research, I selected G/flex from the West System line of adhesives, because of the characteristics of strength and flexibility.

The aluminum sheet was roughed up with heavy sandpaper, and the wood was Sweetgum that was very dry. The Sweetgum in my area is very stable, and when dry, I've had no problems with movement in the past.

The project was successfully completed, and all was well ...... for about two weeks ...., then the wood and aluminum began to delaminate. I knew that it might not work, so there wasn't a big surprise.

The sphere is 5" in diameter with 1/8" sheet aluminum.

Ric


Re: gluejoints

#4

Can you do it with inlays

John Lucas

Rather than cut the wood and glue the pieces together can you route,carve,or turn a groove to inlay the plastic I e had good luck with that technique

Re: gluejoints

#5

Steven Antonucci

why not cast it in clear epoxy?


Re: gluejoints

#6

Re: gluejoints *LINK*

Mike Brazeau

At the St. Paul Symposium, Jerome Blanc from Switzerland gave a presentation on incorporating iridescent acrylic plastic layers in turnings. Just looked at my notes and he mentioned Aqualine L03 glue and Collano. I can't find much Googling. Jerome has been in a couple of American Woodturners and has a website. Maybe you could contact him.


Jerome Blanc

Re: gluejoints

#7

Re: gluejoints

Mike Brazeau

How thick are the walls Rick? One other thing I was going to edit into my post below about Jerome Blanc, was that he mentioned the wall thickness at the joint was about 5 mm and must be perfectly mated. The thin wall minimizes stress as the wood moves and the plastic, or in your case aluminum, does not.

Re: gluejoints

#8

Re: gluejoints

John Zeitner

Thank you, everyone, I'll try the west system and see if I can contact Jerome Blanc.

John

Re: gluejoints

#9

Re: gluejoints

John Zeitner

Hello Ric,

that sphere with aluminum....beautiful job and design...

I did similar things a couple of years ago with wood and pewter-sheet, glued it, believe it or not, with Titebond (green). It has held up untill now, even if the wood shrank a bit and the peweter now shows a faint "edge". Might have to resand it. Now I'd like to do it with colored acrylic.

Thanks for your input

John

Re: gluejoints

#10

Re: why not cast it in clear epoxy?

Jeff Smith

If movement is the mechanism of failure for the glue, couldn't you eliminate the movement by encapsulating the wood in the same type of epoxy used for the glue lines? I used a few bucket loads of West System epoxy while restoring an old ChrisCraft several years ago. When replacing framing and structural components in mahogany, it was common practice to essentially encapsulate the parts in epoxy before assembling. The epoxy is low viscosity and penetrates the surface, sealing moisture out to prevent dry rot virtually forever.

Just a thought