Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

I miss my lathe

Posts

I miss my lathe

#1

I miss my lathe

John Lucas

Well I'm only on my 3rd day of radiation treatment. 17 to go. No problems so far. Rode my bicycle 24 miles yesterday. I'm staying with a friend who lives an hour closer to the Proton treatment center but that of course means I don't have my shop. I was going to start a big pyrography project but lightening got my computer. It won't be fixed until later this week.

Fortunately I will be at the Georgia symposium this weekend and can get my turning fix. Then back to the daily travel and radiation treatments for another 2 1/2 weeks. Then I should be good to go for my demo in Memphis later in October

Re: I miss my lathe

#2

Re: I miss my lathe

Donna Banfield

I empathize with your feelings, John. It sucks. Not that what I'm experiencing is anything close to your treatment, I had surgery mid August to repair a rotator cuff tear in the left shoulder. It may be November before I'll be turning again. Fortunately it's the left shoulder, so I'll get some woodburning and practice with the airbrush by the beginning of October.

Being able to ride your bike is a great way to relieve the mental stresses, too. I hope this temporary break from the lathe means you'll have a tremendous creative breakthrough when you come back :-)

Re: I miss my lathe

#3

Re: I miss my lathe

John Lucas

Donna well I can turn if I was near a lathe. However I can sympathize with the shoulder. I'm still getting over the motorcycle wreck. My wrist and shoulder are still healing after 2 months. Can't do a single pull up or use my left arm to get off the floor. Can only sleep on my right side Still doing really good considering what could have happened

Re: I miss my lathe

#4

Dick Hines

Re: I miss my lathe

Dick Hines

John, just think of all the cool things you can come up with while you are away from your lathe.

Can't wait to see what you will come up with.

Re: I miss my lathe

#5

Re: I miss my lathe

John Lucas

Dick. I designed a piece in my head while being scanned for 20 minutes in the cat scan. I may have to lay still but my mind never stops.

Re: I miss my lathe

#6

Re: I miss my lathe

robo hippy

Well John, you one upped me this time. I am down for a bit after getting a new knee. What you are going through is way more serious. I should be turning in 6 or so more weeks, and probably a week or so of shop clean up before that. Keeping you in my thoughts for a quick recovery.

robo hippy

Re: I miss my lathe

#7

Steven Antonucci

do local clubs lend mini lathes?

Steven antonucci

Ours does...

Re: I miss my lathe

#8

Re: I miss my lathe

Phillip Medghalchi

John, you may be missing your lathe, however, I think it's for the best you wait until you're done with the therapy, I have two friends that went through the same thing and their Dr.s told them no lifting and no strenuous activity for a while. Hopefully your immune system stays strong, also, you may want to make sure you do not go around people who may have any infections of any kind and flu or cold, for that matter.

Now, as far as your shoulder and arm it takes average of 6-8 weeks before it heals, but of course knowing you it may have been in the works already. But having pain and not being able to get up on it is expected this early in the game.

I was going crazy while I was waiting for the head aches and the balance issue to settle down so I can get back into the shop, it kind of feels weird not being able to get behind the lathe. Well, it's a good addiction, though, however, I got lucky that I started the physical therapy right before Jaime came to Kerrville, so it worked out alright. but, still get tired soon and not have that much energy like I did before the incident.

Well, you may want to carry a note pad and put your ideas on paper so when you get behind the lathe you can get cranking full force. You are in my thoughts and prayers and hopefully this will be over before you know it.

Re: I miss my lathe

#9

Re: I miss my lathe

Mark Trenier

Hope your treatments continue to improve your health.

Re: I miss my lathe

#10

Ellis Walentine

Hang in there, John

Ellis Walentine

It sounds like you are keeping a positive attitude. That is a huge part of your recovery process. Keep looking forward to the good times ahead. Your lathe is waiting for you.

Best,

Ellis

Re: I miss my lathe

#11

Re: Hang in there, John

Barry L Elder

+1

Re: I miss my lathe

#12

Re: Hang in there, John

John Stegall

+1 more

Re: I miss my lathe

#13

Thanks everyone

John Lucas

I highly recommend the proton beam therapy if you know anyone who is a candidate. I did a lot of research on different therapies and this one stands out. There are almost no side affects while going throught the procedure. I talked to 3 or 4 of the guys nearing the end of their procedure and they said you will get a little tired toward the end but other than that no problems min fact the doctor doesn't mind if you work out and they have a fitness center on the site m

I'm going to look up various art venues while I'm in knoxville. I drive 1 1/2 each way every day but its almost like driving through the smokies so its a beautiful drive.

I should get my computer back by next week and can work on the drawings for my pyro project. If I finish that and also kill the can we i will feel great and be ready to move on

Re: I miss my lathe

#14

Re: I miss my lathe

Harvey Meyer in Atlanta

Looking forward to seeing you in Dalton this weekend. Safe travels.

Re: I miss my lathe

#15

Re: I miss my lathe

Randy gleckler

If you wanted to borrow my jet mini - and I"m in Knoxville, you'd be more than welcome to it.

Re: I miss my lathe

#16

Don Leydens

Re: I miss my lathe

Don Leydens

Keep up the good fight, John. Who knows what you'll be coming up with in that head of yours. I'm looking forward to it!

Don