Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Woodturners Wonders?

Posts

Woodturners Wonders?

#1

Woodturners Wonders?

Jennifer Indy.USA

Has anybody ordered from or have experience with this company? I just ordered a couple of lathe lights from him on blind faith that they'll be of high quality and work as advertised. I'll report back after they arrive.

Jen

WWW. WOOODTURNERSWONDERS. COM

Re: Woodturners Wonders?

#2

Re: Woodturners Wonders?

phillip Medghalchi

Jen, I haven't., but I did a more frugal way of getting my lights on the lathe. Buy the desk lamps they are selling right now at Walmart for the students the balck one. take off the base form it and then yo have the access to the goose neck and the bulb cone on the top. Then buy a 10 lbs. (I think) strength Magnets from HF drill a hole in them same size as the hole you need for the goose neck. then I bought those 100w equivalent( I guess (23 W) spiral bulb Daylight so you have a very strong real light on the lathe. You can have your light wherever you want it and it won't cost you shipping and handling wither, and no $69.95 for it. In order, for my bulb not to break in case of a blow out form the impact I also, cut some hard metal hardware cloth they use for chicken wire I had laying around and made a cage for it and then used self tapping screw to hold it in place. those light bulbs are little too costly, $13.00 each which I broke two of them when I didn't have the cage around them. Good luck to you.

Re: Woodturners Wonders?

#3

Re: Woodturners Wonders?

Wally Dickerman

Phillip, fluorescent lights don't make a good task light for woodturning. I doesn't cast a shadow so it doesn't show tiny sanding scratches. Incandescent lights at an angle will show them much better. You think the piece is well sanded and when it's out in natural light you find that it isn't.

Re: Woodturners Wonders?

#4

Re: Woodturners Wonders?

ihmserv

Jennifer,

I haven't but a few of the members of local club have good quality and great service and prompt shipping have been the results, haven't heard a negative.

IAN

Re: Woodturners Wonders?

#5

Re: Woodturners Wonders?

Stuart Johnson

Please give us a review of both he dealer and the lamp once you have received it.

Re: Woodturners Wonders?

#6

Re: Woodturners Wonders?

phillip Medghalchi

Wally, I once one a halogen flexible lamp that they sell for $9.00 at IKIA at a drawing in our local club and I use that when I am doing the final cuts and sanding to see those lines you are talking about, but for general lighting I use the one I described. Somehow, I get depressed or tired soon with the incandescent light. Oh, BTW, those light bulbs I use are Day Light brightness. so, they are supposed to illuminate natural light Rays.

Re: Woodturners Wonders?

#7

Re: Woodturners Wonders?

John Lucas

My late wife thought I was tired and depressed in my last shop that was in a basement because I needed "daylight". I spent a rediculous amount of money on daylight fluorescents. Did work at all. Turns out it was the job not the hobby that was making me tired and depressed.

Re: Woodturners Wonders?

#8

Rob Wallace

I have...  Good Quality, Good Service....

Rob Wallace

Hi Jen!

I have previously placed TWO group orders with Ken Rizza at "WW" and both orders were processed and arrived very promptly, well packed, and the items sold were of good quality.

Our first group order was for a group order for the magnetic base LED lathe lights - we ordered about 20 of these and got a good discount. None of the lights had a problem, and our members were very satisfied with these lights.

The second order was for 13 CBN grinding wheels (all 8") -- they arrived within 4 days of payment, and each had a well-fitted box, instructions, and were of very good quality. (These are radius-edged, 8" wheels with 5/8" arbor hole and 1.5" width). A few of our members had previously tried his CBN wheels by ordering individually, and they were very happy with them. With our group order, we saved some shipping costs, and as per his offer for AAW chapters, the Ames Area Woodturners got a free LED light for use on our club lathe.

I would do business with Ken again; he continues to expand his offerings of items for use in woodturning. He is a woodturner himself, and knows what kind of things woodturners are looking for to make their 'at the lathe' activity better and more enjoyable.

Disclosure: I did not meet Ken until after I placed and received both group orders - I met him recently at an AAW Symposium, and we have subsequently become Facebook friends. My association with Ken stops there and I have no interest in his company, except as a satisfied customer.

I hope this answers the original question you asked....

Rob

Re: Woodturners Wonders?

#9

Re: I have...  Good Quality, Good Service....

Jennifer Indy.USA

Rob, thanks! Reassurance. I'll report back.

Re: Woodturners Wonders?

#10

Jennifer, Did you receive

Stuart Johnson

the lights you ordered? If so, how about a review?

Re: Woodturners Wonders?

#11

Love my new Light(s)

Jennifer Indy.USA

I got my new lights and so far I love them. Super bright and the long flexible neck makes it easy to put the light where you need it. I like that the head is small and compact. About 3". Much smaller than I thought it was when ordering but puts out tons of light and doesn't get in my way especially when hollowing. The magnet is incredibly strong so it stays put until you release it with the electronic release on/off switch. It even sits tight on the curved headstock of the Oneway lathes. It will be nice to easily move it from lathe to work bench. It even came with a free little light that I can use at the bench. Small, compact and easy to take traveling. I'd buy this light again for sure.

Jen :)

Re: Woodturners Wonders?

#12

Re: Love my new Light(s)

Don Evans

Jen:

The base on those lamps are NOT electronic, they have a magnet inside them that is round. Think of a can of beans laying on its side that is how the magnet is shaped and laying inside the base.

What you are doing with the ON - OFF switch is turning the magnet 90 degrees and the bottom of unit will stick to metal, turn it 90 deg to off and it will not stick to metal at bottom of base.

Don

Re: Woodturners Wonders?

#13

Re: Love my new Light(s)

Jennifer Indy.USA

Ah, got it Don. I didn't realize what exactly was going on inside the magnetic base when the ON/OFF switch was flipped. Whatever it is, it really sticks!

Re: Woodturners Wonders?

#14

Brad Vietje

Re: Love my new Light(s)

Brad Vietje

Jen,

Did you get the Aurora lamp and get the Galaxy as a freebie as part of the October special? Want to make sure I understand which lamp works so well.

Safe spinning,

Brad Vietje

Newbury, VT

Re: Woodturners Wonders?

#15

It's magic 


Re: Woodturners Wonders?

#16

Re: Love my new Light(s)

Jennifer Indy.USA

Yup, Brad. That's what I got. Love them both. The small one is great for working close up stuff at the bench, and the big one too because it's so easy to move from lathe to bench.

Re: Woodturners Wonders?

#17

Re: Love my new Light(s)

Craig Daymon

Jennifer,

What made you choose the Aurora lamp? I went to the site and the Aurora is not listed as a single product, only part of the sale. The Beacon lamp and Galaxy lamp together is cheaper than the sale price for the Aurora and Galaxy. ($89 vs $105)

I'm looking for a new lamp like this as my cheapie Woodcraft LED lamp has died.

Thanks.

Re: Woodturners Wonders?

#18

Re: Love my new Light(s)

Jennifer Indy.USA

Craig,

to tell you the truth, I didn't compare or even shop much. The Aurora is 5amp compared to the other that is 3amp and it has some sort of magnifying lens over the light. Maybe that's why it's more $$? The offer came in my email and I bit. I guess I'm an easy target. But I'm happy with my purchase. I've been using the Moffat lights on the swing arm and they are really nice but I guess I just needed more flexibility in direct placement of the light and the Aurora seems to fit the bill perfectly. I'm getting old and need more light!

Jen :)

Re: Woodturners Wonders?

#19

Re: Love my new Light(s)

Craig Daymon

Hey, your a woodturner. The fact that you are only "getting" older is a good thing. Most of us feel we are already there.

I have a Moffat lamp, but haven't been using it because of the incandescent bulb in it. I'm going out today to get an LED spot to see if that will do for me. But the smaller lanp, like the Aurora, that might be able to get inside a work would be useful as well.

I definitely need more light. I like doing off axis stuff once in a while and the tremendous lack of light in my shop makes that a real challenge.

Thanks for the response. I wasn't sure if there was more to the decision.

BTW, planning on getting a 5000K spot for the Moffat.

Re: Woodturners Wonders?

#20

Brad Vietje

Old-ER, Jen, but not Old !...

Brad Vietje

...which sure beats the alternative !

Safe spinning,

Brad Vietje

Newbury, VT

Re: Woodturners Wonders?

#21

Re: Love my new Light(s)

David Propst

I used Jen's Aurora light at her amazing Arrowmont class daily last week and will be definitely be getting one. Very bright, small, almost no heat, very positionable, and a rock solid magnet. It was great for detail work at the bench or lathe.

The other thing she turned me on to was a pair of MagEyes. I ordered a 2x strength pair for delivery to use there because I was hogging one of her two pairs so much.

David