Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

3 bowls done this morning.

Posts

3 bowls done this morning.

#1

3 bowls done this morning.

John Lucas

I had to turn these Oak bowls for a friend. I wrapped the wood in plastic bags as soon as I got it. I was worried about cracks because it set behind their business for several days before they called me to come and get it. Then I had a million projects up front to finish and that was just before the motorcycle wreck so the wood set in the bags for about 2 months.

Once I cut the moldy ends off the wood was fine. 2 of them had very minor cracks. I kept a close eye on them but was able to run the lathe fairly fast. Got clean cuts with no tearout so sanding the bowls when they dry shouldn't be hard.

the 2 with the cracks are about 3/8" thick the smaller one is 1/4" I put them in paper sacks to dry because they may not be dry before I have to start the proton beam therapy and this should keep them in good shape until I finish that and can get back in the shop.

I still haven't had time to put up my netting to keep the shavings at bay. These were small bowls and I still had shavings 8 feet away. I covered the table saw, jointer, and horizontal bandsaw. Still had some shavings on the bandsaw table but brushed them off for the photo so they wouldn't rust the table anymore. Bear in mind this is half the mess I usually have when I turn bowls larger than 9".




Re: 3 bowls done this morning.

#2

Re: 3 bowls done this morning.

Dick Coers

Curious how you are going to sand around those beads? I've always found it difficult to hold details when you have to sand green turned to finish. Not being able to power sand on the lathe adds to that difficulty. End grain of course is the worst.

Re: 3 bowls done this morning.

#3

Dennis in Southern Oregon

Re: 3 bowls done this morning.

Dennis in Southern Oregon

John, kind of curious what kind of netting you plan to use. I would think that netting would collect chips big time. Will that be a problem?

Dennis

Re: 3 bowls done this morning.

#4

Re: 3 bowls done this morning.

John Lucas

Dick I run them on the lathe at extremely slow speeds. That allows me to crease the sandpaper and run in inside the beads. These were cut clean enough that I could easily sand them by hand off the lathe if necessary but I find if I use a light touch and really slow speeds I can usually sand on the lathe.

Re: 3 bowls done this morning.

#5

Re: 3 bowls done this morning.

John Lucas

I bought something resembling mosquito netting at the Walmart fabric area. I plan to cover the top edge with duck tape and punch holes for shower curtain hangers that are S shaped so I can remove it easily if needed. I may have to weight the bottom since it's pretty light. I just haven't had the time to hang any kind of rail.

Re: 3 bowls done this morning.

#6

Re: 3 bowls done this morning.

phillip Medghalchi

Waite a sec. i thought last time I found you the link to those guys who sell these big large netting for the mosquito which supposed to cover a two door garage entrance you said you already found them, and now you said you bought something at Walmart? I am thinking of buying that materil and using the shower curtain rail that they use for RV's or in the ER that separates you from other patients then by having that over head then you can maybe push it to one side and pull it around you when you are turning, so most of the time it's out of the way. Let me know how it goes,plz.

Re: 3 bowls done this morning.

#7

Re: 3 bowls done this morning.

John Lucas

It may be a while before I get it installed since I go to the doctor tuesday to start the procedures for the radiation therapy. That will kill all shop work for about a month.

what I plan to do is cut it into 1 foot wide segments so I can walk through it anywhere to get to my tool cabinets, grinder etc. That should let me move it closer to the lathe to better contain the shavings. Since it breathes maybe I won't get so hot and the fan can blow through it. We'll see. I'll certainly post photos when I get it set up.

Re: 3 bowls done this morning.

#8

Re: 3 bowls done this morning.

phillip Medghalchi

John, here is an idea, I am planning on keeping it at the whatever width it comes in. Then, overlap about 3 inches where the next section comes in and then few use magnets (not rare earth magnets) so when I need to get through it I just undo the magnets, and get to the other side and meanwhile the magnets and the 3 " overlap should keep the shavings under control, I will post the pic. too if I get to it before you do. We should come up with some answer soon.

Re: 3 bowls done this morning.

#9

Re: 3 bowls done this morning.

Barry Irby

Why not use the Strips like they have on the big back doors at Lowe's and other Borgs or the little ones they use on the dairy case at the grocery store?

You could use a track like they used on vertical blinds.

Re: 3 bowls done this morning.

#10

Re: 3 bowls done this morning.

John Lucas

Barry those clear curtain strips you see in the stores and factories are really w

Expensive. I started to just cut up clear shower curtains but that would block the wind and my shop is already too hot.

Re: 3 bowls done this morning.

#11

Re: 3 bowls done this morning.

Barry Irby

I have a huge piece of aviary netting left over from my son's hobby of keeping wild ducks. I can't imagine how you would keep the shavings out of it. Wonder what else would work?

Re: 3 bowls done this morning.

#12

Re: 3 bowls done this morning.

John Lucas

Barry. I found something similar to mosquito netting that i purchased. Don't know when I'll ever get to try it out. Ill be living away from my house for a month during the radiation therapy. And then I'm going to look at selling my house and moving so my shop work may be radically reduced for the next 2 or 3 months. Not looking forward to all of this but it has to be done

Re: 3 bowls done this morning.

#13

Wow.....

Barry Irby

I don't think I could stand that much turmoil. I just found out my urologist retired. Got to start again with the prostate stuff. Not looking forward to it. Hope yours goes well. I've been in the same house for 35 years. I shoudl move too, but have feet of clay.

Re: 3 bowls done this morning.

#14

Ric Taylor

Re: 3 bowls done this morning.

Ric Taylor

John,

So sorry to hear about your illness. Let me be the first to welcome you to the survivors' club. All will be well in due time, as I found out.

Ric