Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

New Rikon Grinder

Posts

New Rikon Grinder

#1

Dennis in Southern Oregon

New Rikon Grinder

Dennis in Southern Oregon

I spent the morning installing my new slow-speed Rikon Grinder. It has been on sale recently at Woodcraft for $100. The final results are very satisfactory; with two D-Way CBN wheels, it is very smooth and virtually silent. On small nit: the shafts are a bit on the short side so I had to find some thin washers to use under the shaft retaining nuts so that I could get a nearly full threading of the nuts. The dimensions and mounting hole layout of the unit are quite different from those of the Delta grinder that it replaced so it took a bit of redesign to incorporate it into my OneWay sharpening system.

Re: New Rikon Grinder

#2

Pic? "...into my OneWay sharpening system"

Henry W

"... so it took a bit of redesign to incorporate it into my OneWay sharpening system."

I couldn't let this comment pass without asking for a pic? Please do show us what you mean here.

Henry

Re: New Rikon Grinder

#3

Re: Pic? "...into my OneWay sharpening system"

phillip Medghalchi

Ditto

Re: New Rikon Grinder

#4

Dennis in Southern Oregon

Re: Pic? "...into my OneWay sharpening system"

Dennis in Southern Oregon

I did not mean anything very deep here. It's just that the V-arms of the OneWay Wolverine system need to be properly located vertically and horizontally relative to the grinder wheels. This required me to raise the grinder a bit and re-locate one of the arms to match the narrower wheel spacing of the Rikon wheels.

Dennis

Re: New Rikon Grinder

#5

Re: Pic? "...into my OneWay sharpening system"

phillip Medghalchi

Well the set up says that it has to be set up so the grove in the v section is inline with the mid line of the wheel, so the min, you go changing the wheels to something else you have to redo all that again. I had to do this when I got my Rikon replacing the woodcraft brand grinder I had, but when I consider buying the CBN wheels I have to do the same you did. relocation them all over again. right now I do not have enough HSS tools to justify the high dollar for CBN yet. I do like Rikon vs. the wood craft grinder I had, I tinker with it for so long to get it running true until one of my very good pro turner freind caught on to it and told me the problem was the grinder shaft itself. I am happy with Rikon now. runs very quiet.

Re: New Rikon Grinder

#6

Bill Blasic

Re: Pic? "...into my OneWay sharpening system"

Bill Blasic

The Rikon grinder I bought when they first came out runs absolutely perfect right out of the box, quiet and smooth. I was surprised though to find it a little shorter on the width and like above I had to move the jig bases to make all work. A good buy!

Bill

Re: New Rikon Grinder

#8

Question regarding your set up

David Walser

Since you're using CBN wheels, which are solid metal and cannot come apart like standard grinder wheels, can you remove the rest of the wheel shrouds from the grinder? If you were to do that, would it give you a little more length on the grinder shaft? It would seem that removing the shrouds would make setting up the grinder with CBN wheels even easier.

Okay, that's two questions. Sorry.

Re: New Rikon Grinder

#9

Re: Question regarding your set up

John Lucas

Yes you can remove the guards but it won't change the length of the shaft screws at all. The crews that actually held my guards on touched the wheel slightly so I simply ground them down and put the guards back on. Not sure why but I just felt like I should keep the guards with the machine.

Re: New Rikon Grinder

#10

Dennis in Southern Oregon

Re: Question regarding your set up

Dennis in Southern Oregon

Yes and no, David. Yes, I could remove the shroud, but no, it would not give me any extra length. The usable length is determined by a shoulder on each end of the shaft against which the the CBN rests. There is at least a quarter of an inch of clearance between the wheel and the shroud. Thinking about it some more, I believe that I could simply omit the washers on the outer sides of the wheels.

Dennis

Re: New Rikon Grinder

#11

Re: Question regarding your set up

phillip Medghalchi

Dennis, when you Figure it out. let me know, plz. I like to know fore the future buy of CBN.

Re: New Rikon Grinder

#12

Re: Question regarding your set up

Matt Overton

John, I have been trying to get you by email, but didn't see a response. Give me a call or email me 215-778-3091 mofuels@hotmail.com. Thanks

Re: New Rikon Grinder

#13

Dennis in Southern Oregon

Re: Question regarding your set up

Dennis in Southern Oregon

I checked out the issue of whether washers can be omitted at the outer ends of the shafts. The answer is a qualified yes. By omitting the washers, I get slightly more than full thread through the nuts. However, the apex to apex diameter of the nuts is only about 3/16" larger than the bore of the CBN wheel that contains the spindle adapter. (This means that if the nut were 3/16" smaller, the wheel could slide off of the adapter and over the nut and on its merry way.) There probably is no real risk here, because it would take thousands of pounds of axial pressure to shear off that 3/16" of nut. However, it offends me enough that I am going to use thin washers and give up about half a thread of nut closure.

Dennis

Re: New Rikon Grinder

#15

Dennis in Southern Oregon

Re: Question regarding your set up

Dennis in Southern Oregon

I don't know Stuart. I did not need a thinner nut, but one with a larger outer diameter. My old Delta grinder, which this replaces, has the same shaft size, but the outside of the nuts are quite a bit larger. Unfortunately, they will not screw onto the shaft of the Rikon. If I had bothered, I could have taken one of the nuts to the local Ace Hardware and probably found what I needed. (Or maybe not; the thread TPI may be in Chinese inches.)

Dennis

Re: New Rikon Grinder

#16

Re: Question regarding your set up

phillip Medghalchi

you may be able to grind the thickness down very carefully on the sander to regain a thread or two, that way you do not have to go to the hardware store. But very carefully as not to grind it unevenly.

Re: New Rikon Grinder

#17

Re: Question regarding your set up

Steve Worcester.

That's a really good question (embedded).

Do you need the guards if the wheels won't explode?

I shimmed them and have them on the Baldor because they still offer some safety for the gouge going off the edge. Although I use a SharpFast system that centers the gouge and won't allow it to go off the edge, but I still want that level of safety I guess. Free grinding or even using a oneway, would allow you to stray from the center.

Re: New Rikon Grinder

#18

Dennis in Southern Oregon

Re: Question regarding your set up

Dennis in Southern Oregon

Personally Steve, I do not see any significant advantage for me in having them on when using CBN wheels. The only possible advantage that I can think of is that they channel sparks so that they can eject only towards the front. If you store your chainsaw gas behind the grinder, this might be an issue.javascript:insertTags(":D"); I left the inner shrouds on just because it was easier to do so.

Dennis