Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

the good news and the bad news

Posts

the good news and the bad news

#1

the good news and the bad news

GaryG in MD

I recently bought a pen kit and the associated bushings from a to-be-unnamed retailer. The bushings were not the right size, in several respects. I don't know the country of origin, but I think we can all take a stab at it.

Anyway, I decided to just turn them down to size. (Yes, they were THAT far off.)

So I did. Not a problem.

I keep a couple rare earth magnets stuck to my banjo for easy access to use for whatever need may arise -- sticking something to the lathe, keeping my design papers from blowing away, etc. Needless to say, I found that the magnets had sucked up all the turning shavings from the oversized metal bushings. Well, I thought, that's nice. The metal shavings didn't blow all over the place and contaminate me or my lathe. True. But have you ever tried to get metal shavings OFF a RE magnet? You can suck a few off with a powerful vacuum with a brush head, but you can NEVER get them all off. So now I have a fuzzy RE magnet. I may have to just trash it. OR keep it for this purpose again in the future. Another little lesson learned... ...GG

Re: the good news and the bad news

#2

Re: the good news and the bad news

Bruce Pratt

Try a stronger (or more) magnet(s) under a sheet of paper. The filings should be attracted to the stronger magnet and accumulate on the paper sheet.

Re: the good news and the bad news

#3

Ric Taylor

Re: the good news and the bad news

Ric Taylor

Have you tried getting the fuzzies off with the sticky side of duct tape?

Re: the good news and the bad news

#4

Re: the good news and the bad news

phillip Medghalchi

Gary, how funny, and coincidental, I have this large pick up magnet close by all the time and at times I have to get in there and grind something off around the lathe and you guessed it right it gets mixed up with the shavings. Anyway, I always had hard time getting the metal shavings off the darn thing so I can see what else I dropped off along the stuck wood shavings and everything else. I pricked my fingers with the metal shavings bad fedw times and finally figure out that old sucks wrapped around the head of the magnet at the handle would work and it doesn't because it gets fuzzy from the shaving ripping it, So, one day I went by the local alteration lady and asked her for her scraps of the inner lining of the skirts or coats (the very slick lining that they put in them) and that was the answer to it. I have it secured with a twist tie around it and then i pick up whatever shavings then if they are very sharp then I just throw the cloth away or as soon as you shake it over the trash can you can retrieve the cloth and reuse it again. In your case, you are just throwing away maybe size of quarter each time, but your RE magnets which are not cheap ( I paid 13.00 + for a 1/4'x 1/2" fiver of them at woodcraft) and very strong are are too expensive to toss them, plus your alteration lady around the corner would be happy too. And, if you have a stronger magnet around maybe you can get the other shavings off your RE ones w/o tossing them. Of course, do the same trcik on the larger magnet to save your fingers.

Re: the good news and the bad news

#5

Re: the good news and the bad news

John Lucas

I just don't worry a out it. As a mt worker as well as wood many of my magnets have shavings. I just pluck off what I can with my fingers and let it go. I suppose you could apply the sticky side of tape. To it and peel it off and probably get most of them

Re: the good news and the bad news

#6

Don Leydens

Re: the good news and the bad news

Don Leydens

I use my air compressor to blow metal shavings off. Gets about 99% of them.

Re: the good news and the bad news

#7

Re: the good news and the bad news

phillip Medghalchi

John, I hope you took out AFFLAC as your protection for the hands and skin. :D

Re: the good news and the bad news

#8

One word: Plastic

Bill Houghton, Sebastopol, CA

I use the plastic bags our newspapers come in during the rainy season.

Re: the good news and the bad news

#9

Re: One word: Plastic

phillip Medghalchi

Bill ,then you can not recycle that one. It's mixed up with metal shavings. Hey, we gotta give back to the earth. Think green, but if that frees you form worries, then by all means, go for it. Most of the time they end up, up on a tree like they were flowers polluting the environment anyways. :D

Re: the good news and the bad news

#10

And the answer is...

GaryG in MD

How silly of me not to think of it.

The same answer to ALL shop questions.

DUCT TAPE!

Unlike John, I have a strong aversion to metal shavings, and I just HAD to get rid of them. It wasn't easy, but after a number of iterations, they were on the duct tape and not on the magnet. Well, most of them, anyway.

Thanks, all, for you good suggestions.

This one worked pretty well for me. ...GG

Re: the good news and the bad news

#11

Steven Antonucci

On metal shavings:

steven antonucci

First, if you've ever missed a wooden splinter, you'll likely wake up next day and know about it because it will start to get infected. However, if you've ever had a sliver of metal in you hands (e.g. steel wool or grinder bits), you will see a black dot that won't come off with soap. Likely, it won't even hurt.

Metal is "compatible" with our chemistry. Wood is not. After a day of metalworking, I usually find all kinds of small things in my hands, and I've never had any issues. Wood usually takes a day or so to heal after you've removed the splinters.

All around my grinder and metalworking bench, there is all kinds of metal dust and such. To clean it, I usually use a rare earth magnet inside of a paper towel or a plastic bag. I put it in the compost pile, assuming that the earth's core is basically all iron, and metal occurs naturally...so I am recycling. By having it inside of the towel or bag, nothing sticks once I remove the magnet. It is a huge PITA to remove them if you put the magnet down in the wrong place, so I just dedicate a couple of magnets to this purpose.

S

Re: the good news and the bad news

#12

sounds good to me!