Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Distant woodturning connection

Posts

Distant woodturning connection

#1

Steven Antonucci

Distant woodturning connection

steven antonucci

I started in earnest carving spoons, spatulas, and ladles a couple of years ago. I had made a handful prior to that, but I can tell you that in the last 2 years, it has been almost on equal footing with woodturning for me.

My carving club, the Jersey Hills Woodcarvers, demonstrates in the home and hobby section of the NJ State Fair. This past weekend, I spent almost 20 hours with a knife, spoke shave, draw knife, or spoon gouge in my hand with only one minor nick to show for it. (handle of the draw knife came off)

On Friday night, I ran over to my cherry log to grab a could of small crooks for making spoons/ladles. They've been down for almost 2 years, and sit in a pile that is probably close to two cords in size. I brought them into the shop and bandsawed them into ladle and spoon blanks.

Saturday AM, I packed the truck and ran up to the Fair with my camping chair, those four tools, a handful of spoon blanks and my portable lapshave. (it is a small shave horse based upon Robin Fawcett's plans) You can see it to the right here:


Working at a leisurely pace, I roughed out this ladle in an hour or so.


Since the wood comes from a branch crook, the grain runs all of the way through it. However, being in a branch, it is under a lot of stress. They sometimes get a mind of their own. I usually work them down to about 1/4" thick, and then let them dry a week or so. I wrap them in paper bags (just like a green bowl ...turning connection #1!) I did 5 that day.

Michael Hosaluk (turning connection #2!) demoed at our club a couple of years ago, and he showed us how to use the microwave to steam bend. I wrapped this in a damp kitchen towel for 2 minutes on high, and then clamped it up.


It probably sat in the clamp for 20-30 minutes, and here is the result:


You cannot tell in the original picture, but the original handle was bent this severely in the opposite direction. There was a minimal amount of spring back, and almost no raising of the grain because it is a cut surface (no sanding).

I will oil it in a couple of days when I have the other 4 finished.

Questions or comments always welcome.

Steve

Re: Distant woodturning connection

#2

Re: Distant woodturning connection

dick gerard

Now that's a really nice ladle! How much does it hold? And what sort of price would I expect to pay? Just in case SWMBO says I can have one ....

Re: Distant woodturning connection

#3

Re: Distant woodturning connection

Barry L Elder

Nice work, Steve. I appreciate tools and utensils made from wood that are actually usable on a daily basis.

Re: Distant woodturning connection

#4

Re: Distant woodturning connection

John Lucas

Funny you should post this I have been using my shaving horse and doing some microwave bending as well. Hope to be able to show it soon.

Re: Distant woodturning connection

#5

Steven Antonucci

Portable Lapshave *LINK*

steven antonucci

In the world that we live in, it is nearly impossible to be "unique". Google anything, and you'll get page after page of results.

Except if you google: lapshave.

Robin Fawcett posted a picture of his based upon a drawing I found on Pinterest.

I built mine in a half day, and I kick myself for not doing it earlier. It is portable, weighing in at maybe 4 pounds? If I wanted to, I could run the 2x4's I used through a thickness planer and make it 3 pounds. I carried it by the belt strap on my shoulder with a bungie cord and a camp chair. I may make pack straps for it, or at least pad the strap.

I actually may never use my full sized horse again...

S


Bodger's bord

Re: Distant woodturning connection

#6

Re: Portable Lapshave

RCH

Now that looks interesting and useful, and a size that would also be more friendly. Thanks for posting the link.

Re: Distant woodturning connection

#7

nice work, Steve!

GaryG in MD

You're clearly having too much fun. ...GG

Re: Distant woodturning connection

#8

Steven Antonucci

Here is a better picture (with mod notes)

steven antonucci


Originally, the deck that sits on my lap was longer and wider. It was much more comfortable use with the deck narrowed to this profile. The underside was chamfered with a draw knife.

The flat angle on the dumbhead was rounded, but it didn't grab at all because the hole was essentially concentric with the circumference. The flat is nice because I can reverse the dumbhead (flat forward or rearward) and it accommodates a lot of holding THICKNESSES.

I also knocked off the corners of the platform because I got tired of banging my knuckles on them.

I lost both of the ringed nails in the two pegs. I may put in two golf tees if I can find them, or I may just turn two golf tees.

It is also certainly possible that I will shorten the foot bar, as it doesn't need to be that long, but does make it more stable when I take it off. This is how I stand it when I am not using it. When I am done, it will fold nearly flat, and then I wrap the belt around it to secure it. Otherwise, you get pinched carrying it. DAMHIKT.

I LOVE THIS THING!

S

Re: Distant woodturning connection

#9

Re: Here is a better picture (with mod notes)

Keith Newton

Thanks for sharing this shot. I may have to make one, but I'm thinking all hand hewn material would be in order.

Re: Distant woodturning connection

#10

Steven Antonucci

2x4's are better

steven antonucci

I made it out of 2x4's because my outdoor one is white oak and it tends to dent the work if I step too hard. I want the material to be softer than what I am working on. And even with pine, it still can dent the work.

Also, if it was a hardwood, it would weigh 2-3X what it weighs now.

So, hew if you must, but hew pine...

S