Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

My hats off to those who teach

Posts

My hats off to those who teach

#1

My hats off to those who teach

Mike Potts

I know from reading the forum some of you teach turning one on one. I have a young gentleman that has been helping me around my place, and he asked me to teach him how to turn a bowl. With all the help he's been I couldn't say no, then I found out he wanted to give it to his grandmother for her birthday, and decided to try and take a video. Trying to teach is a hard enough job, but trying to run a video really stretched the limits. This video was done on the spur of the moment so it's not great, but but I'm pretty sure grandma will enjoy seeing her grandson make her a special present. And yes I know Doug's last name is Thompson, been to his shop a couple of time to buy tools. It took over 5 hrs from start to finish for the bowl. Wow you guys that teach really have to have a lot of patience. My hat is off to all of you.

Safe Turning

Mike

www.youtube.com/watch?v=qac5WdDq3Yc

Re: My hats off to those who teach

#2

Dan Jechura

Re: My hats off to those who teach

dan jechura

very nice

Re: My hats off to those who teach

#3

Re: My hats off to those who teach

phillip Medghalchi

Mike, that was a very nice teaching, you did very well coaching him through it. I was concerned about two issues there. Even though that he started out staying out of line of fire at the beginning before the piece came to a full speed I, I noticed he move directly in line of fire in roughing out stage and he stayed there most of the time. I think in this stage is the most important time to stay out of line of fire like maybe to the right of the lathe towards the tail stock and have the tool rest tilted little more towards the bottom of the bowl so you are gradually shaping from the bottom up to the rim and blank steady itself little at a time and you are not in line of fire. and, also makes it easier to tighten up the tail stock as you go to have the blank staying put. Secondly, and most important that for a beginner you let him wear a full handed fingered glove around spinning blank on the lathe that it has been told is very dangerous. I am glad no accident happened there and you guys managed to finish the project, however, it's been noted by all the pros that you should not be wearing a full handed glove around the lathe. Unless you have had a long time experience around the lathe. He also, took his face shield off when he was working in the bowl trying to hollow it out and smoking. I am not personally a smoker, but I'd be careful around shavings of wood when the ashes form the cigarette keep falling out and he is not really shaking it off since he has his hands full with the gouge, so it'd dropping off on the shavings around him on the floor that can ignite wood.

I appreciate what you did for this young man and yes indeed teaching someone else is not an easy job to do, however, you did it well and more than likely he already got bit by the turning bug, believe or not. He is on the right track for a healthy hobby instead of getting involved with non-healthy alternatives of the activities. We all thank you.

Re: My hats off to those who teach

#4

I noticed the left hand was not .......

JamieDonaldson

...anchored to the tool rest, and that lessens control of the tool significantly. The tool rest is the fulcrum as well as reference and support for controlling a cut, and without that anchor point many bad things can happen when poking the tool into spinning wood! I teach the push cut first, rubbing the bevel, out of the line of fire, before introducing the pull or shear cutting.

Re: My hats off to those who teach

#5

Re: My hats off to those who teach

robo hippy

I had to look at one part twice. He really was sanding with a lit cigarette in his mouth.... No kind of fire, under any circumstances, in any wood shop, ever!! Knew a smoker who dropped his lit cigarette down the dust collector hose. At least he was able to get out of the shop....

robo hippy

Re: My hats off to those who teach

#6

Re: My hats off to those who teach

phillip Medghalchi

I am not a smoker, but about two months ago, I was roughing out one bowl and it got so hot on my tool that heat made some smoldering dust and it fell off on the shavings bellow and I didn't pay attention to it until it started to burn a hole in my anti fatigue amt under my feet and luckily since my lathe is closer to the garage door opening I managed to put it out quick and got lucky other wise it would have been a disastrous situation. I can't even imagine having the cigarette burning and I can't remember the proper term for the ashes that hang on to the tip of the cigarette while you have it in your mouth that the smoker has to stop and flick it off, but I know that has been reported to be number one cause of many fires in many arson, I agree with Reed, that's a NO-NO around the shop i don't care what you do in the shop. Specially wood shop.

Re: My hats off to those who teach

#7

Re: My hats off to those who teach

John Lucas

If your shavings or the tool is that hot your doing something wrong. Either the tool is dull, your pushing too hard or the wood is going too fast or all 3. I've had shaving come off on dry wood bowls that are hot enough to be uncomfortable on my left hand but not anywhere near hot enough to burn anything

Re: My hats off to those who teach

#8

Re: My hats off to those who teach

phillip Medghalchi

John, I am not sure what happened that day, and what all took place. I never had that happened to me before, I am sure your diagnostic of the problem is very accurate. One of those factors played the role in that mess, the point I was making is that smoking around anything in the shop is too dangerous for a little pleasure it offers in smoking a cigarette vs the risk. I appreciate your comment, after that incident I am very careful and sensitive as how hot the shavings get if any and stop and let things cool off and check the process more often.

Re: My hats off to those who teach

#9

Re: My hats off to those who teach

Barry L Elder

Now that everything has been critiqued and complained about, Mike, you did a heck of a job teaching him in such a short time. You are to be congratulated! My first bowl took all day and all night and I didn't sand or put finish on it 'till the next day. I'm sure his Grandmother will be so very pleased that he made it for her!!!

I would like to salute all the teachers in our Country, especially those who teach the children who are our future. Actually, any teacher who teaches anyone anything should be saluted for their efforts. I just wish the true teachers could get paid what they are worth to our public school system in spite of the politicians.

Re: My hats off to those who teach

#10

Smoking issue

Mike Potts

Normally I'm the only one in my shop so I've never felt the need to post " NO SMOKING". As I stated in the first thread this was my first time trying to teach turning, his first time on the lathe, and then I threw in trying to take a video. you may notice that the sanding segment is the shortest, while I was setting up for sanding, getting the camera going He lite up, I didn't notice till I started the video going, we then stopped and had a little discussion about smoking in the shop, enough said.

Re: My hats off to those who teach

#11

Re: My hats off to those who teach

phillip Medghalchi

Barry, I did compliment his effort and commended it. He did a great job finishing it in 5 Hours ( according to Mike's explanation in the video), after all. I was just worried that a future young turner would be safe and enjoy this trade for many years to come and not become a statistics. That was the intentions of my comment not to critique it in any other ways. Even though that we may teach someone else, it is very important to teach them about the safety so they can truly enjoy what they are learning and be grateful for it.

I am hoping that Mike didn't take it personally.

Re: My hats off to those who teach

#12

Mission acomplished

Mike Potts

Spoke to my young friend at my granddaughters birthday party last night. He told me how he had taken the DVD and bowl to his grandmothers and first gave her the DVD to watch then right before the end had given her the bowl. She was very pleased and thought he should take up a new career. I could tell from his telling of the story that here was a sense of pride in being able to make this gift with his own hands. In this day of computers, video games, and smart phones very few people will experience that feeling. Dan & Barry thank you for your kind comments, and yes again a salute to all the teachers out there. There is a old saying " Those that can, do. Those that can't teach" I think maybe that sometimes those that do, have forgotten they had to learn from someone.

Thanks & Safe Turning

Mike

Re: My hats off to those who teach

#13

Re: Mission acomplished

Scott Daniels

Mike, great for you passing on knowledge! My wife is a teacher and she tells me "remember teaching is a learning process too". It is easy for others to point out the "never in my shop" moments, but remember all of us had to learn these at one time or another. I also have learned for my better half we all (and some of us only) learn from mistakes! At times I only learn from mistakes. You have, it sounds from grandma's comment, inducted a new member......GOOD FOR YOU.

Re: My hats off to those who teach

#14

Thanks Scott