Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Using walnut oil or tung for sanding

Posts

Using walnut oil or tung for sanding

#1

Using walnut oil or tung for sanding

phillip Medghalchi

" David Walser , Wally Dickerman"

Can any one of you explain the process for me please? I have used Mahoney's finish on one of my bowls and had unexpected result with it. Now I hear you folks use walnut oil to sand, I am hoping that it's not the expensive one above?

Re: Using walnut oil or tung for sanding

#2

Re: Using walnut oil or tung for sanding

Wally Dickerman

I wet sand using the same oil that I use to finish my bowls. In my case that's usually Daly's Ben Matte tung oil but any finishing oil will work. I just apply some oil to the wood and proceed to sand. I replenish the oil as it's needed. I mainly use oil with the heaviest grits. Don't drown the wood in oil. You'll be surprised at the results. If you're sanding with 120 the wood will look like you've sanded with 180. Reason is, the sandpaper clogs with oil slurry. Don't overuse the Sandpaper....As the saying goes....use sandpaper like your brother in law is paying for it.

A real plus... no dust.

Re: Using walnut oil or tung for sanding

#3

Re: Using walnut oil or tung for sanding

phillip Medghalchi

Wally, thank you for replying. Let me ask you if this procedure only works for the oil finish? That you have to use the same oil which you would finish your final finish with? Or, let's say I want to apply this method and then use General finish salad bowl finish to finalize the finishing process, would it work or the salad bowl finish will not adhere to the previous oil which is soaked into the wood?

I understand that by doing this you use the slurry and fill the little holes and the end grain areas and also, the wood gets replenished with the water it lost during turning process, am I thinking it right?

I once saw a guy on you tube that he used tung oil on a piece of spalted pecan then he finished the piece by applying sanding sealer and lacquer, I emailed him about it and he has not responded yet, so I think my thought on lacquer use is not correct?

Re: Using walnut oil or tung for sanding

#4

Re: Using walnut oil or tung for sanding

Joe Herrmann

I generally use Watco Oil to finish my pieces followed by lacquer with no problems. I also sometimes wet sand with the oil as well and then follow up with lacquer, again with no problems. I used to use boiled linseed oil cut with thinner as the first step but have since gone to the Watco because it was more convenient. I still use the BLO on flat work followed by either poly or lacquer.

I've also sanded using paste wax followed by lacquer with no problems.

Re: Using walnut oil or tung for sanding

#5

Re: Using walnut oil or tung for sanding

Wally Dickerman

I've found that you can apply most any finish after oil sanding.

Re: Using walnut oil or tung for sanding

#6

Re: Using walnut oil or tung for sanding

David Walser

Like the others have said, I've had good success using other finishes over wood that's been wet sanded using walnut oil.

Mike Meredith, of Doctor's Woodshop (one of the makers of walnut oil based finishes), has several youtube videos out on the use of his products. Here's a link to one on wet sanding with walnut oil: https://www.youtube.com/watch?v=MUDqE8x1TTs

Hope this helps.

Re: Using walnut oil or tung for sanding

#7

A word of caution...

mjonesrdg

Top coating a straight oil (especially walnut oil) is not recommended unless it is allowed a very long time to cure. The problem is not a 'compatability of finishes' problem, but rather, is a problem of sealing off the oxygen supply before the oil is fully cured. Mike Mahoney told me personally, that the walnut oil may never cure in the wood in these conditions. Lee Valley publishes a page of instructions for use of their walnut oil http://www.leevalley.com/us/shopping/TechInfo.aspx?type=a&p=59385

and they call for 3 to 6 months cure time.

Rancidification, will continue however, as there is ample dissolved oxygen within the oil to perpetuate the deterioration of the unsaturated fats which are the cause of rancidity. I don't know if having rancid oil inside of a bowl (or other item) would present any future problems or not, but apparently Mahoney and Lee Valley think that it might.