Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Help - design for portable lathe bench

Posts

Help - design for portable lathe bench

#1

Help - design for portable lathe bench

Geoff Whaling

I see a new wood lathe in my future - some longer term planning - in fact I have placed an order for a new mini/midi lathe replacement for our 12yo Nova Mercury. I'm on the hunt for suggestions for a portable(ish) bench and ideas perhaps plans or links to good setups someone has seen. I've seen many variations about but I want to go a little more upmarket from the standard Gorilla alum work platforms. We currently use a Jet stand

Basic requirements each component has to

• be stable

• be portable preferable a one man lift so nothing over 15kg with a 20kg max. (lathe plus add-ons is 60kg plus so a two man lift)

• easily assembled

• offer practical working access

• be able to roll away after use.

• have drawers for accessories.

• and be self cleaning - I wish.

I would appreciate any assistance or links to good setups as I saw a compact roll away workshop some time back but can't find it again.

Re: Help - design for portable lathe bench

#2

Re: Help - design for portable lathe bench

John Stegall

This design meets some of your criteria

http://www.ibuildit.ca/Woodworking%20Projects/lathe-stand-1.html

Look around his site for some ways to mobilize it. Try woodgears.ca also. Check out their "reader built" links too.

Re: Help - design for portable lathe bench

#3

Re: Help - design for portable lathe bench

Bill Turpin in WNC mountains

Mount two non-swivel castors on the outside of the legs under the headstock. Mount them on the side of the legs pointing horizontal instead of vertical. The wheels should be only a 1/4" off the floor. Have extensions(~18") for hands sticking out from the tailstock end. This makes the stand into a hand truck. Pick up on the handles and the wheels will touch the ground, allowing assembly to be rolled anywhere. Hand extensions can slide in and out for more compactness. Basic idea can be changed in many ways and for many different types of equipment. Castors should be at least 2" diameter and a weight rating for entire load. Have fun!

Re: Help - design for portable lathe bench

#4

Re: Help - design for portable lathe bench

John Lucas

Geoff I purchased the metal stand for my Delta Midi. I found some quick release knobs to replace the standard nuts on the bolts that hold the stand together. Then I turned the bolts upside down that hold the lathe to the stand so the threads are up. Now I can store the lathe and stand in the trunk of my car in pieces. It takes about 3 minutes to assemble the stand and then the lathe just sits on top. If I think it's necessary I have nuts to hold the lathe onto the stand.

This is very light weight, although the lathe itself is quite heavy, about 100lbs I believe. The stand is very light and rigid although the metal on the bottom was kind of thin and wouldn't hold the rolling wheels I put under it. I added a piece of angle iron to the bottom and made the wheel attachment quite solid,

Re: Help - design for portable lathe bench

#5

Found the orig

Geoff Whaling

I found the original website - turned out it was a Fine Wood Working article

http://www.startwoodworking.com/post/roll-away-workshop

I'm still very keen to hear of ideas or see photos of setups others have built for themselves. Thank you for the ideas so far.

Re: Help - design for portable lathe bench

#6

Jim Barbour

Re: Help - design for portable lathe bench *LINK*

Jim Barbour

I needed one for a jet mini some time back so I could easily take it to shows,etc. The Porter Cable chop saw stand fit the bill nicely. I think got the idea from Cindy Droza, but am not completely sure. At the time I was moving everything in a Honda Element and this setup fit just fine. The link is the first link I found.


http://www.factoryauthorizedoutlet.com/porter-cable/porter-cable-universal-mobile-miter-stand

Re: Help - design for portable lathe bench

#7

Re: Help - design for portable lathe bench

William Duffield

Something like this might do in a pinch, while you design and build something more permanent.


This is the setup we use with our JML-1014 and WorkMate when our club does demonstrations at our local woodworking show. The rock maple work surfaces on the work mutt are, or course, a custom enhancement, and you wouldn't need the blast shield in your shop, even though it is a necessity when demonstrating in front of the public. Without the blast shield, you might want to invent a mount for a work light.

If you have a larger mini-lathe, and especially if you are turning off-balance stock, some extra weight on the lower shelf helps a lot with stability.

Re: Help - design for portable lathe bench

#8

Re: Help - design for portable lathe bench

Scott Bradley

Someone at my turning club had a pretty good setup the other day. It was a crate with casters on one end for easy transport and a leg set and the lathe was bolted to the top and would hinge up so that the crate became the bench. You could close the top, lock it, flip the legs up and be on your way. handles for lifting or pulling. I guess you could put some ballast inside if you wanted after flipping the lathe into position. The box would also make a good place to hold tools and accessories while doing a demo. I'd probably put a power bar on it too. I wish I'd paid more attention to the legs.

Re: Help - design for portable lathe bench

#9

Re: Help - design for portable lathe bench

Scott Bradley

Someone at my turning club had a pretty good setup the other day. It was a crate with casters on one end for easy transport and a leg set and the lathe was bolted to the top and would hinge up so that the crate became the bench. You could close the top, lock it, flip the legs up and be on your way. handles for lifting or pulling. I guess you could put some ballast inside if you wanted after flipping the lathe into position. The box would also make a good place to hold tools and accessories while doing a demo. I'd probably put a power bar on it too. I wish I'd paid more attention to the legs.

Re: Help - design for portable lathe bench

#10

Re: Help - design for portable lathe bench

phillip Medghalchi

Geoff,

I bought this portable table a long time ago when it was $50, but you can buy this and use it for many of your tools to hook it up on just change the top and then drill holes where your tools will connect. it will fold to a small space and if youdo not want to use the extensions then leave them at home or just set them aside until you need them for miter saw.

http://www.harborfreight.com/mobile-folding-power-tool-stand-40612.html


Re: Help - design for portable lathe bench

#11

Joe Fleming

Re: Help - design for portable lathe bench

Joe Fleming

Geoff,

If you are looking for transportable, the suggestions here are excellent. I have used the B&D WorkMate for a mini lathe on the go. It works great. The chop saw stand looks good too.

At home now, I have a "movable" lathe stand. I build a cabinet that is the right height, but is narrow like a lathe. It has casters so I can roll it around the shop, but I would not consider this transportable. It has doors and drawers, as needed. The Fine Woodworking article you referenced is a good starting place for that. On my cabinet, I used a chunk of butcher block for the top. I added a power strip, a student desk lamp, and built-in switches on both ends for on/off and reverse. My lathe is the little Vicmarc, so I have a separate motor that required switches. Joe

Re: Help - design for portable lathe bench

#12

Thank you - any more custom setups?

Geoff Whaling

Thanks for the pics & ideas, much appreciated. I'm looking for a more custom setup and trying to avoid the commercial stands etc. So hopefully we may see some more custom semi portable or at least mobile lathe benches.