Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Fastener name?

Posts

Fastener name?

#1

Fastener name?

Craig Daymon

I have a project that I would like to use a type of fastener I have seen before, but do not know what it is called so I can't find it to buy.

They are typically brass. One half is a flat head machine screw and the other half looks like a brass tube with a cap on the end. The tube is threaded on the inside and the machine screw screws into the tube.

Anyone know what these are called?

Thanks in advance,

Craig

Re: Fastener name?

#2

Re: Fastener name?

Darryl

they are a jewelry fitting. Try Rio Grande

Re: Fastener name?

#3

Re: Fastener name? *LINK*

Guy Bratt

I was thinking your looking for these. I get them at the hardware in the small parts bins. You could also try mcfeelys.com online catalog page 21 bottom of the page. I hope this helps.


http://en.wikipedia.org/wiki/Sex_bolt

Re: Fastener name?

#4

Re: Fastener name?

Craig Daymon

I think that looks like what I want. Bit surprised by the name. I've seen them use to bind a stack of paper/cards, which is what I need it to do. I'll try McFeeleys/Enco/McMaster-Carr. Just didn't know a name for them.

Thanks.

Re: Fastener name?

#5

Joe Fleming

Re: Fastener name?

Joe Fleming

Go to the office supply store. They sell them there too.

Re: Fastener name?

#6

Found them.  Chicago Bolts *LINK*

Craig Daymon

Called Lee Valley and their customer serivce got me the name. They are called, Chicago Bolts.

McMaster-Carr also has them. They can be found by searching on "Chicago Bolts". The page refers to them as "Low-Profile Binding Posts".

Thanks.


Chicago Bolts at Lee Valley

Re: Fastener name?

#7

Re: Fastener name?

robo hippy

They look pretty typical of knock down hardware used in furniture a lot. There have got to be a million different types.

robo hippy

Re: Fastener name?

#8

Re: Fastener name?

phillip Medghalchi

Craig, you should be able to find them in specialty drawer sections at lowe's under this name. "barrel nut, barrel bolt". I am not sure if they carry them in brass or nut.

Re: Fastener name?

#9

Re: Fastener name?

Barry Irby

I always thought they were Sex Bolts, for obvious reasons, but I guess the Politically Correct Police have banned the use of that name.

I bought barrel bolts at Lowe's and other places and they were different. What I got was a cylinder with a hole drilled through it sideways and threaded. I used them to fasten a bed together. 3/4" diameter steel rod with a threaded 3/8 hole through it. Drill a 3/4" hole through the leg from the side and a 3/8" hole from the direction of the rail. A bolt embedded in the rail locked the rail to the post. The 3/4" holes were plugged. Same concept as hiding a square nut in the rail or post, but you can drill for it and install the barrel nut later.

Re: Fastener name?

#10

Re: Fastener name?

Craig Daymon

I've bought barrel nuts before and have had my share of knock-down furniture (and I think I have some in a drawer somewhere in the shop). What I was looking for are not what I have considered to be barrel nuts.

Still, like I said, I found them at both Lee Valley and at McMaster-Carr by searching on the name, Chicago bolts.

I was a bit surprised I had to get various sizes. If the tubes were long and threaded all the way, I could have just trimmed the tubes to the desired length. They seem to only have about a 1/4" of travel.

Re: Fastener name?

#11

Re: Fastener name?

r payne

I've seen them listed as binding posts, chicago screws and sex screws (or bolts). They are available threaded completely through or partially threaded. The last time I needed a few, I bought them from Tandy leather. I've also seen them (in Al) from Lowe's, Home Depot, Fastenal and Menards.

Re: Fastener name?

#12

Re: Fastener name?

Craig Daymon

I did check Menards. They didn't have them. At least not in brass. I didn't look for other materials. They may have had the plastic ones. Though now that I have valid names for them, it should be easier to find them. That's what I was looking for was the correct name. Once I had that, it wasn't too hard to find them.

I find McMaster-Carr and Enco to be good places to get things like this, unless you are certain you will only ever need one. Usually implies a quantity purchase.