Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Carving On Turning

Posts

Carving On Turning

#1

Carving On Turning

Tom Henderson, Gulf Breeze Fl

I have an interest in learning to add carving to the turnings I make. The ones I have done so far appear as if I had used a jackhammer. So I need some advice...

I plan to start with a small set of carving tools. Do I need a set for relief carving or for carving in the round?

What is the best way to sand the places I carve to obtain the same surface finish as the uncarved, which are sanded to 600 grit.

I have one book by a fellow named Pye. Are there others, youtube videos, etc.?

Are there other tools you might recommend, dremels, etc.?

Re: Carving On Turning

#2

Re: try this

Darryl

suggest you look at the power carver at http://www.woodcarverssupply.com/Micro-Motor-Tools/products/72/

runs about $200 but worth it. Burs from Rio Grande in addition to others. You need something that will turn up rather fast. The air powered units are a bit pricey to start but will not wander as much as a dremel. The above power carver can be used for any sanding. Get the 3 M disks and mandrels from Rio Grande. They are a jewelry company but have a considerable amount of stuff you will want. Darryl

Re: Carving On Turning

#3

Re: and this

Darryl

Contact Dixie Biggs. She does super work on bowls and such. Her work is fantastic and she shares her knowledge. From your post I assume you are thinking about hand tools. I's suggest you consider the power carver in my other post. Darryl

Re: Carving On Turning

#4

Re: and this

John Jordan

There's a couple of articles on my website (under articles)about carving that show some of my tools and methods. "carving" is not really descriptive of what you want to accomplish, and there are many ways to go. Pick something that you like and start there. I usually suggest to students that they start with textures. DON'T carve on a nice piece until you have put in some time practicing.

Have fun.

John

Re: Carving On Turning

#5

Re: Carving On Turning

John Lucas

My advice is to pick a tool and just start using it. Gear your turning and projects toward designs that you can accomplish with that tool. they don't have to be fancy.

My first carving tool was a woodrasp, coping saw, and various sandpaper glued to sticks of different shapes. I still use all of that today.

I bought a Dremel and then learned what all I could do with it. It's amazing what you can do with that one tool. With patience the Dremel will do an awful lot. The Foredoms and High speed air tools will do some things faster and easier and you can easily step up to those later.

Hand carving is fun if you really learn to sharpen. I'll say that again. If you really learn to sharpen and keep them sharp. It's a chore if you don't. They will do some things that power tools won't do, The reciprocating carvers make some jobs easier and you can screw up faster so there is a learning curve just like all the other methods.

I hand sand most carvings. You can glue sandpaper to sticks using 3M spray adhesive. This speeds up some sanding processes. For the most part it's simply starting with a course enough grit to get the job done removing tool marks from whatever method you used to get there. I'll power sand where I can and often use those 3M sanding starts for some jobs.

I will second and third the recommendation to learn from Dixie Biggs. Not only is she really fun she's full of useful knowledge. Still haven't made the little tiny sanding discs by using leather punches and Dremel mandrels that I learned from her an one symposium last year but I will.

Re: Carving On Turning

#6

Re: Carving On Turning

Jorge

Tom,

Learn to carve with a few simple gouges, just pushing them, you need to learn to keep them very sharp, and use your head so no flesh is ever in front of a cutting edge. Stay away from power carvers until you know how to carve by hand, then you don't need a power carver... Knives are also great carving tools, besides chisels and gouges...

Re: Carving On Turning

#7

The old reliable X-acto carving .......

JamieDonaldson

......knives are also very useful for much of the carving I do on my turnings. Readily available and very inexpensive. ;)