Reed, watched your video, a lot of good tips. I've been sanding at 135 rpm I guess i"ll have to change the belt and get into low range,I can get down to 50 rpm. I really like the tip on stopping the lathe and getting those tool marks that seem to hang out in just one little section. Hey thanks for taking you time to make this video, not very much info on these two areas.
Sort of reminds me of my warm weather passion, fishing Lake Erie for yellow perch & walleye. All kinds of different fish and ways to catch them, more that enough experts to tell you how to do it (all with different opinions) But once the piece is turned or the fish landed, their done. But there still needs to be sanding (cleaning the fish) and finishing ( cooking the fish) before we have a beautiful piece or great fish dinner. Keep doing what your doing, thanks agian
If you are sanding bowls that have been twice turned (green turned, dried, and then turned again so they are round) you can sand at higher lathe speeds. Still, the slow speeds just seem to cut better. I will thank Vince Welch of Vince's WoodNWonders for starting me on that trend.
Of course, the better your turning technique is, the less sanding you need to do.
Reed, I turned an 11'x 3 1/2" maple bowl this morning. I always single turn my bowls green. I have to thank you as the sanding went much fast & better. Where did you get your " big eraser" I checked Vince's site last night and didn't see one.
They do slightly extend life of the discs. The curious thing about the blue discs from Vince is that they can feel dull with your fingers, but when put to the wood, they still seem to cut very well, so I don't always use the finger test (not while the disc is spinning of course) to confirm if it is time to get a sharp disc on. Probably another important part of sanding is figuring out when it is time to toss the old disc.
I am not sure which one of Vince's sanding pads you are using, if they are blue he sweared that since they have a film backing they last longer. I spent a lot of money two years ago on getting almost 50 of each grit from 80-800 grits and didn't have very much luck with them. Specially, his back up pads tore up after two weeks and he didn't seem to cared when I took them to the SWAT to change them out he acted like he was not interested in customer service after the sale. And ,when he went to give me another one he acted like"here get out of my way" he was busy trying to sell to someone else instead of taking care of he one who spent the money and had trouble with the product. So, I decided to go else where. Recently, I have bought cloth back Klingspor 3" sanding disks and it held up to the point that I was very surprised. I can put it on the back up disc holder and then use it by hand and still will cut very well.
First please let me apologize if I offended you in anyway which clearly it sounds like I have. What I have found is my blue film discs do not tear as paper backed discs might as they become worn and I do share that information with people. If the backup pads you are referencing were yellow perhaps I can better explain. I had carried the yellow pads for nearly 10 years without issue until the last shipment. While they looked perfect on the outside there were some in the shipment that were faulty and just fell apart! It took me some time before I was aware there was an issue! I simply had no idea! I pulled those pads immediately once I was aware of the issue! Please understand that I speak to many, many people throughout the year and I try to coach many people as they describe there sanding processes breaking down and are looking for help. After talking with these folks often it is discovered through conversation the breakdown is due to sanding too fast and burning up Velcro or trying to sand a natural edge bowl, getting a catch, and wondering why the foam tore... etc. etc! Please hear me carefully as I am not saying these examples pertain to you but again it took me a minute to understand some of these pads were faulty! I truly apologize for your experience with those pads if that was the case. More importantly, I also apologize to you as I clearly offended you while in my booth. There are some 800-900 people attending SWAT the past few years. In my booth I have one other person in addition to myself working with folks. This is in no way an excuse for poor behavior however there is always a character or two in the crowd so to speak and I sometime I get taxed! Please understand! Finally, it is very clear to me I am here to provide the very best products and the very best service period! I value each and every turner and whomever they are with as they visit my booth! What I would like to suggest is you call me toll free 1-877-284-8969 or my cell 502-500-4264 so we may discuss how I can make this right for you. In addition, I would like to ask you to please reintroduce yourself to me at SWAT this year (it will be here before you know it) so I may apologize to you in person. I truly value each and every turner and look forward to seeing friends sharing stories and making new friends each year, each symposium. Vince
If Vince has not or does not respond to your situation/experience, please call him directly. I have used Vince's products sonce the first year he was in business ... and that has been a long time! I have never had a problem that he was unwilling to resolve. And I really like his products ... to the point that I will not use any other sanding disks. I really suspect that your experience at SWAT was one where Vince was overwhelmed by customers. It happens. I used to work for a woodworking store and my small claim to fame was that when everything was hectic crazy over the top out of control ... I was the one who kept his head and plowed on through. Not everyone can do that.
I have advocated slow speed sanding for years ... and it works for me. Especially on woods that are prone to surface checking like cherry. Heat is the enemy of both wood and velcro. Slow down the rotation of the wood and the sanding disk.
If Vince has not or does not respond to your situation/experience, please call him directly. I have used Vince's products since the first year he was in business ... and that has been a long time! I have never had a problem that he was unwilling to resolve. And I really like his products ... to the point that I will not use any other sanding disks. I really suspect that your experience at SWAT was one where Vince was overwhelmed by customers. It happens. I used to work for a woodworking store and my small claim to fame was that when everything was hectic crazy over the top out of control ... I was the one who kept his head and plowed on through, even thoughI was as overwhelmed as everyone else. Give Vince a second try, I'm sure he will make it right.
I have advocated slow speed sanding for years ... and it works for me. Especially on woods that are prone to surface checking like cherry. Heat is the enemy of both wood and velcro. Slow down the rotation of the wood and the sanding disk. The sanding medium will last longer, the velcro and foam will last longer and the wood surface will definitely benefit.
I really love your analogy about fishing and can definitely relate. You said you always turn and sand green bowls to finish. I would suggest that you try Abranet for sanding. It doesn't load up like other abrasives, and if it does it can be washed in water or solvent and used more. It works especially well on green wood, but I now use it for almost anything and find it doesn't leave scratches like normal abrasives. The Abranet discs or sheets you get from most places is incredibly expensive, but I get mine in rolls from the San Diego Woodturners and it's reasonably priced. Check with them to find out where they buy it in bulk (www.SDWT.org/). I started cutting it in discs but it was a pain. I now usually just cut it in squares and find the corners soften the edges much like "wave" discs do. I love the stuff.