Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

More Faceplates and Glue Blocks vs Chucks & Tenons

Posts

More Faceplates and Glue Blocks vs Chucks & Tenons

#1

More Faceplates and Glue Blocks vs Chucks & Tenons

Wally Dickerman in Arizona

Just an example of why very often using a chuck and tenon isn't the answer. It would be very difficult to finish the bottom beads on this small beaded HF when using a chuck. The chuck would be in my way....Ummm...I was going to show my beading tool...forgot.




Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#2

Re: More Faceplates and Glue Blocks vs Chucks & Te

Steve Worcester.

I don't see how a chuck would be in the way anymore than a faceplate and the waste wood.

But my other question is, do turn on the backside of the lathe? It doesn't appear the picture is flipped (based on the txt on the tool rest).

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#3

Re: More Faceplates and Glue Blocks vs Chucks & Te

Wally Dickerman in Arizona

Yeah Steve, I'm a lefty and often turn in in reverse on the outboard bed of my lathe. Do all my hollowing there.

I can tell you from experience that a tenon in the glue block and the extra width of a chuck is in the way of my beading tool for the last few beads. Plus being a knucklebuster when working that close. The faceplate just works better here.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#4

Brad Vietje

Wally's Beading Tool

Brad Vietje

... is right there, in the first photo, second from the right, right ?!? :D

I agree that the chuck would be a little more obtrusive, and certainly more of a knuckle-busting shirt grabber. One could always work the narrow base area after reversing and turning between centers, no?

Beautiful work, as always, Wally.

Safe spinning,

Brad Vietje

Newbury, VT

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#5

Re: More Faceplates and Glue Blocks vs Chucks & Te

Steve Worcester.

In this context, both would work. The benefit of a faceplate would be it won't move with a catch as in hollowing.

I favor a faceplate if I have the material. But I still don't see how one would be better than the other in this case. But, what works for you works. No contest.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#6

Re: More Faceplates and Glue Blocks vs Chucks & Te

phillip Medghalchi

Wally, thanks for sharing, I do agree that it's safer this way and also, it gives you more versatility to maneuver around the skinnier throat of the vessel.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#7

Re: More Faceplates and Glue Blocks vs Chucks & Te

Craig Daymon

One real advantage to glue blocks over tenons is that you can make the most of a beautiful piece of wood. That being said, I haveput a glue block on a piece of wood and then chucked the block. In hindsight, probably would have been better to use a faceplate in that case.

I do see a difference in FP and glue block vs chuck. If I hit the chuck with my tool, trying to get a little too close it is much worse than hitting the glue block, which shouldn't be any worse than the turning I am doing in that area of the piece anyway. I always turn down the glue block relative to the piece, making it easier to get in where I want to cut.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#8

Re: More Faceplates and Glue Blocks vs Chucks & Te

John Lucas

nobody has mentioned the one downside to faceplates. turning into the screws. Although it's not a major thing but just like trying to get too close to the chuck when you start wasting away wood to get down to the neck like on Wally's vase it's really easy to go to far and cut into the screws. They can take a pretty good chunck out of a gouge.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#9

Dick Hines

Re: More Faceplates and Glue Blocks vs Chucks & Te

Dick Hines

I don't ever expect to see the beading tool. You have been hanging that carrot in front of us for years. :D

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#10

Re: More Faceplates and Glue Blocks vs Chucks & Te

Wally Dickerman in Arizona

John, I'm always aware of the screws and their length when using a faceplate. My glue blocks are one inch thick so it's never a problem. I should mention that when using a glue block and an endgrain blank as this one is, I cut a small tenon on the blank and a corresponding opening in the glue block. Makes a good secure glue joint.

Dick, my beading tool is left handed so it wouldn't work for you anyway. :(

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#11

Steven Antonucci

a left handed bead is much harder to cut!


Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#12

I use a tenon also. Extra safety always pays off


Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#13

How do you lock your faceplate?

Geoff Whaling

Wally,

I'm more interested in how you lock your faceplate while turning in reverse & hollowing?

With modern lathes I can really see no reason why they can't be used in LH or RH mode other than the safety aspect of unscrewing accessories from the headstock spindle. So most curious how you solve that issue. As a rightie doing a lot of small spindle stuff I've often reckoned lathes are built wrong.

John,

I use glue blocks a lot and in combination with faceplates or chucks. Just depends upon the application. As for cutting into screws - why would you want to do that? ;-) Screws shouldn't go past the waste block & your planning should have allowed for removing waste from the block for access to the main piece without going near the screws.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#14

Re: How do you lock your faceplate?

Wally Dickerman in Arizona

My lathe is a Oneway which has a hardened spindle with a groove cut. Oneway faceplates and chucks have grub screws to lock into the groove, making them secure for either right or left handed turning. A great feature. Much of my turning, including hollowing, is done over the outboard bed with the lathe turning in reverse. Some turners are finding that hollowing in reverse while reaching across the bed of a lathe works very well. You can see better what you're doing. Ask J Paul Fennell or Don Derry.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#15

Re: How do you lock your faceplate?

ron bauer

My Powermatic faceplates have two set screws for locking when reverse turning. If yours don't it is a relatively simple matter of drilling and tapping for a 1/4 x 20tpi set screw. Locate it so the screw seats on the unthreaded portion of the spindle.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#16

Steven Antonucci

Why not just turn normally and stand on the right?

steven antonucci

I've seen Don Derry do his demo and try to explain why he runs the lathe backwards? I didn't get it? Why not just stand on the right side of the ways?

S

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#17

Re: More Faceplates and Glue Blocks vs Chucks & Te

Dick Hnes

I can turn left handed. Do it all the time

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#18

Okay Dick...Just For You...

Wally Dickerman in Arizona

Here's a pic of my left handed beading tool....


Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#19

Re: Why not just turn normally and stand on the ri

Wally Dickerman in Arizona

Well I guess you could do that, in fact I've tried it. But then it wouldn't be lefty turning would it. My last lathe was a custom Nichols lathe that was lefty only. Left hand threads on the spindle. Before that I did a lot of hollowing on the outboard bed of my General 260...and before that an old Delta outboard bed....Normal? Guess I'm not. But at 93 I'm still doing it...

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#20

Dick Hines

Re: Okay Dick...Just For You...

Dick Hines

Wrong end, Wally,wrong end

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#21

Re: Okay Dick...Just For You...

Craig Daymon

Hey, he's a lefty. Maybe that is the end he cuts beads with? Maybe he's just...that...good. Besides, those lefties are an odd lot. :b

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#22

Re: More Faceplates and Glue Blocks vs Chucks & Te

Mike Potts



Here is a little experience I had last week with glue block. I had just finished turning the inside of a 12" bowl. must not have been paying attention as I pulled the gouge out I caught the edge of the bowl. 1/3 of it went flying across the shop the rest stayed in place on glue block. put a nice dent in my tool rest.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#23

Re: More Faceplates and Glue Blocks vs Chucks & Te

Bernie Rose

Don't EVER accuse a lefty of doing anything with the wrong hand. I once kidded (I thought) a

surgeon for writing a prescription with the wrong hand and I had to go back to Michigan two months later to get my hernias repaired properly. He must have used some kind of post-surgical witchcraft.

Re: More Faceplates and Glue Blocks vs Chucks & Tenons

#24

Re: How do you lock your faceplate?

Geoff Whaling

Wally, thanks I figured that would be the case. I'm not familiar with the Oneway setup haven't seen one in Oz. I don't have to worry about LH turning with my Woodfast M910 VS (conv for an older M908) as Woodfast won't fit reverse to them here. Most of my faceplates have the grubscrew fitted.