Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Easter eggs

Posts

Easter eggs

#1

Dan Jechura

Easter eggs

Dan Jechura

Had some time on my hands and decied to practece tool control. The practace ended up easter eggs. They are not finished. The eggs are Apple, Oak, Spalted Oak and Maple. Big ones and normal size ones. The bowl they are in is made out of spalted Maple, the grass is wood shavings. The proble is how to hold the eggs to finish the ends. Anyone have any ideas. I have 36 more to do so I hope to get better at making them. Comments welcome. Thank you for your time





Re: Easter eggs

#2

Re: Easter eggs

Emmett Manley, Lakeland, TN

I make a lot of eggs and I use the same method you demonstrate in your first photo. I finish and sand the pointed end with the tailstock removed, then cut off the less pointed end from the headstock with a thin skew making rounding cuts and sanding as much as I can before the final parting.

I gave up using various jigs in an extra step to jam chuck to finish the ends as I found I could do just as well, and a lot quicker, using a thin skew. Making eggs is great skew practice. I've also been known to use a scraper in order to refine the curves.

Eggs are not symmetrical with one end being more blunt and one pointed. I try to make my eggs 60 mm long and 45 mm in diameter -- that being about the size of a large hen egg. So, the first thing I do is turn a cylinder 45 mm in diameter, then mark off 60 mm, plus a mm or two for the live center point.

Re: Easter eggs

#3

Dan Jechura

Re: Easter eggs

Dan Jechura

Basically what I did. The problem was some of the eggs broke off and I had to saw off the extra. So a lot is need to be removed. I am thinking about makinging something with a plastic pipe and a band clamp. I saw that some where.


Re: Easter eggs

#4

Re: Easter eggs

Gerald Klug

I use a collet chuck made from an ABS plumbing fitting. Slice eight saw cuts to make the fingers flexible and clamp the egg in with a hose clamp. I learned this method from Dick Sing.

Re: Easter eggs

#5

Dan Jechura

Re: Easter eggs

Dan Jechura

What do you attach the fitting to?

Do you have a photo?

Re: Easter eggs

#6

Re: Easter eggs

John Lucas

Dan Just turn a chuck out of wood. Grip in in your chuck, drill out the inside to the size you want. Turn the outside and then cut a bunch of slices into it on the bandsaw and put a band clamp on it. I turn a groove for the band clamp so it doesn't just fall off. You can make any size you want in minutes.

I do what was suggested above. I use the toe of my skew to sneak up on a very small tenon. Leave the tenon smallest just a short ways away from the egg. That way if it breaks off it doesn't pull fibers out of the egg. Then just carve this away and sand by hand.

Re: Easter eggs

#7

Re: Easter eggs *LINK*

Mike Brazeau

I made this egg chuck a number of years ago modifying what I found from Dick Sing. Have Dick's book now after his visit to our guild last year. Doing again would thin the maple down a bit to make jaws more flexible.


Egg chuck

Re: Easter eggs

#8

Steven Antonucci

Instead of rechucking, how about...

steven antonucci

making a small concave fixture that you could hold in the chuck and line it with a little velcro/padding so you could use it to sand the ends of the egg? Just hold the egg in your hand an push it? The velcro would give you the ability to change grits as necessary.

S

Re: Easter eggs

#9

Re: Instead of rechucking, how about...

Don Orr

I chuck a sanding disc in a #2 MT Jacobs type chuck, mount it in the headstock and sand off the little nub. Easy to change grits as needed. Yours look good-mine are all over the place in shape and size. You think you know what an egg looks like til you try to turn one. :D :\ :O

Re: Easter eggs

#10

Re: Easter eggs

Jerry Klug

I hope I am attaching a pic of my egg jig. It has been a long time since I posted a pic.

Re: Easter eggs

#11

Re: Easter eggs

Jerry Klug

The picture turned out real bad. The chuck is epoxied to a home made face plate made from artificial wood decking and threaded to match my spindle threads. If you make one of these chucks, be sure to be careful of the clamps. It is a good idea to either wrap them with tape or fit an elastic band from a sock over the clamps.

Re: Easter eggs

#12

Vacuum chuck?

Mike Brazeau

I have thought about making a vacuum chuck shaped to the egg contour with some cushioning but have never got around to trying.

Re: Easter eggs

#13

Dennis in Southern Oregon

Re: Vacuum chuck?

Dennis in Southern Oregon

Given the small square-inch crossection of one of these eggs, I doubt that you would get enough holding force with a vacuum chuck to be stable unless you shaped the chuck to fit the finished end of the egg. If you merely gripped the egg at the center, there would be half an egg length of leverage aiding the tool force to rotate the egg out of position.

Dennis

Re: Easter eggs

#14

Re: Vacuum chuck?

John Lucas

I agree. I've turned 3" mirrors on the vacuum chuck and you have to take very light cuts. That's with 3" of surface. An egg probably has half that if not less. You would have to make a chuck to fit the egg very closely. If your going to do that you might as well make the chuck we talked about above and forget the vacuum.

Re: Easter eggs

#15

Re: Easter eggs

bowlman

I have been turning eggs for some 20+ years now. I really got started on eggs as a lucky accident. My wife and I were at an egg themed restaurant and we were looking over some advertising pics for my turnings. The owner/manager of the restaurant came by and noticed the pics and asked about them One thing led to another and he asked if I ever considered making wooden eggs. So we made a deal and I made some small eggs on spec and one egg 3" diameter and another 4" diameter. He liked them so much he purchased all I had and has been a regular customer ever since. I have probably turned and sold just to him, over 1000 eggs in various sizes. Back whem I was doing craft shows, I would have several egg cartons filled with wooden chicken eggs, each one a different species. They sold especially well in March and April ... close to Easter of course.

Based on an article in one of the early Dale Nish books, I made a series of egg chcuks similar to what is so well presented by Mike. They served me well until I retired from my mortgage paying job and my wife presented me with a vacuum chuck system.

The small eggs do require a light touch, but if you have done your between centers work properly and have just a small tenon to remove and sand, they work fine.

The larger eggs of course can easily be held by a larger vacuum chuck. regardless, the egg chcuk is best used for light finishing cuts, not for shaping and taking off lots of wood. I have an album over on WOW that has pictures if anyone is interested in looking at it. This thread just proves that there is more than one way to skin a cat ...

Re: Easter eggs

#16

Steven Antonucci

Egg shaped recess in vacuum chuck?

steven antonucci

Wondering if a vacuum chuck with a recess turned in that sealed around the diameter of the egg would work? You'd be pulling on a three dimensional surface area, so it is probably substantially larger than you'd think?

The inner recess would be "egg shaped and tapered at the outer edge to accommodate eggs of +/- 1/2" diameter difference?

I wouldn't part the egg off to leave the center mark on the waste piece. Once it was centered with the tailstock and running true, you could remove it with a skew or detail gouge and sand away.

Steve

Re: Easter eggs

#17

Steven Antonucci

How do you hold the cat on the lathe?

steven antonucci

assuming you wanted to skin him? Vacuum? Cat Chuck? LOL

S

Re: Easter eggs

#18

Re: Egg shaped recess in vacuum chuck?

John Lucas

Probably would but as I said above you would have to make each egg exact or very close so you might as well just build the screw clamp jig. It takes me about 5 minutes to make one.

Re: Easter eggs

#19

Steven Antonucci

Let's think about that?

steven antonucci

Not so sure? I can see it being an issue with a flat surface like a mirror, but an egg surface is much larger than the diameter, and I think the vacuum would plull against the entire curved surface??

If you had a 2" chuck on a mirror, it would pull against an area pi*r^2 (which would be Pi in area since R=1)

If you had an egg with a 2" major diameter, with the egg set inside the chuck, the area is actually the entire surface of the upper egg, and much larger than pi. The holding force would be probably 3X or more.

You have to remember, the vacuum exerts against the entire surface area, even if it is round. I suppose an easy way to test it would be to take your household vacuum hose and put and egg against it? (I'm not going to try it, just in case the egg breaks... I'm married, and I wouldn't need that much grief...)

S

Re: Easter eggs

#20

Dennis in Southern Oregon

Re: Let's think about that?

Dennis in Southern Oregon

The relevant area for purposes of computing vacuum force on the egg is the cross-sectional area at the point (actually ring) of vacuum seal. The maximum possible area therefore is pi x r-squared, where r is the maximum diameter of the egg. The shape of the egg inside or outside of the ring of seal is irrelevant.

Dennis

Re: Easter eggs

#21

Dan Jechura

Re: Easter eggs

Dan Jechura

Thank you all for you help and ideas. I am following some of them except skinnibg the cat. :D :D

I'm getting better, I just need to make the egg chuck so I can sand them. More pic's to come.