Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

URNS

Posts

URNS

#1

URNS

Bernie Rose

Some time ago it was recommended that the interior of urns be coated with epoxy to make them air, and moisture proof, thus preventing the ashes from forming a solid ball from the moisture. My question is the

HOW to get an even coat of epoxy on the whole interior ? If the epoxy is introduced to the interior while still on the lathe there would be either a missed point at the bottom or an overflow coming out the mouth , making a terrible mess on the lathe. I would appreciate any instructions from those who have had experience in the procedure.

Re: URNS

#2

Re: URNS

John Veerkamp

Am I missing something? Unless the urns will be shaken(why) , what difference does it make if the ashes clump?

Inquiring minds want to know.

Re: URNS

#3

Re: URNS

Dale Miner

I don't put finish on the inside. I advise folk to put a good quality plastic bag inside the urn and fill the bag. Seal the bag with a twist tie.

Re: URNS

#4

Re:

John lucas

Bernie. My experience is very limited. 2 funerals and 2 different places did the cremations and I built the urns. In both the ashes were placed In plastic bags inside the urns. I don't know if that's how it's done everywhere.

Mix you epoxy so its fairly thin or if necessary heat it water. Then pour it in and slosh it around and pour the excess out. Then put it on the lathe and ru. It real slow for as long as you can. My friend built a system using a rotisserie motor that rotates 3 homemade threaded spindles so be can do that many and dries them over night

Re: URNS

#5

Re: URNS

Pete in Holland MI

You could thin some polyurethane or shellac and pour & tumble it around then inside a couple times to build up a finsh.

You vessel most likely has a finish on the outside, thus should be considered part of the ash barrier.

A plastic bag is a probably course of action. That's what I'm planning on the vessels for my parents. Not planning on opening it up and checking out the ashes afterwards, thus, what happens to them in the vessel is not a concern to me.

Pete

Re: URNS

#6

Ric Taylor

Re: URNS

Ric Taylor

John,

The world of what happens to cremains is a very personal and private one. Many urns are made in a way that they are not permanently sealed closed. They often have a threaded lid or some other means of opening.

What families use as urns and where they keep them varies widely. Some are obviously urns that are prominently displayed in the home. Some are other types of containers that you would never guess hold cremains. Some on kept in the back of a closet. You would be surprised to know how many families are keeping cremains in their homes as traditional burial becomes less popular.

Often as time goes by, families make decisions to further distribute the ashes. They may decide to distribute the ashes among adult children or adult grandchildren, or they may decide to scatter some ashes in a special place or places. There are companies that sell rings and lockets that are designed to hold a bit of ashes, and sometimes someone wants to open an urn to retrieve a bit of ashes to place in the jewelry. This is not at all unusual.

Many urns are designed to hold more than one person, such as a married couple. Those urns need to be opened at a later date to add the additional cremains.

For these reasons, urns are often designed so that they can be opened at a later date, and the ashes are commonly held in a plastic bag within the urn to help keep them from clumping.

The urns I make all have threaded lids.

I hope this helps to clarify,

Ric

Re: URNS

#7

Re: URNS

Bernie Rose

My concern was to keep the ashes dry so that a later date samples could be removed for smaller mini-urns in case the culture changes enough so that my ashes could be divided up amongst several great grandchildren or those down the line. And who knows what developments will take place in the scientific world that would make cremains a valuable source of medical information, leading to a cure for cases of redundant contagious hyper- proliferative phimosis.

Re: URNS

#8

Re: URNS

phillip Medghalchi

Bernie, how about put few good medical descants in the urn along with the ashes in a sealed bag, or if you have food bag sealer the ones you use to use to put food in the freezer, then when the time comes they can cut the seal open and take out what they need for the distribution. Oh, BTW, when you put any thing in the fire of that much heat it will burn any disease or bacteria and viruses, so I don't thin any scientist going to find anything to study there.

Re: URNS

#9

Re: URNS

Pete in Holland MI

It's interesting that some folks deem it acceptable to have small samples of ashes broken up and given to other people for various reasons, but it would be offensive & creepy, and possibly against the law, to have jars with preservative with fingers, toes, and other body components on the shelf in memory of. Same result, different format.

Build a wood project, a photo, or a legacy to have your next of kin yourself by.

Me......unless I become a Saint, they can keep me together when I get put away in either an urn or coffin. I have no intention on ending up on a fireplace mantle.

Pete

Re: URNS

#10

Answer +

Mark Mandell - Gone Round In New Jersey

Hi Bernie,

I have been coating urns with epoxy for a number of years. After finishing the piece, I apply masking tape around the opening, mix the coating with what I estimate will be more than enough, and then pour it into the jar followed by tilting and rotating the piece slowly to allow the epoxy to run/sag around the interior surface sometimes helped with a long brush (clean immediately in DNA). I then pour out the excess into the mixing cup. The coating left inside will tend to slump so I invert the jar to allow the coating to drip out into the cup (the tape protects the outside surfaces). As the mix begins to thicken, I pour it back into the jar for a second tilt/rotate effort and then invert it and allow it to again drain. The amount that "drains" will be pitched unless I have another use for it before it sets up. Depending on the wood's porosity I may repeat this with another mix. Spalted wood will absorb more.

Now, all that said, I had occasion to research the clumping issue, and contacted the American Cremation Society. "Ashes" are actually the ground/granulated skeleton (all soft tissues leave nothing behind in the cremation process - no fingers etm. will exist ;) ) and the people I spoke to had never heard of the moisture clumping issue nor had that problem, even though I had previously been told of it by several funeral directors. I had also seen such statements over the years on web forums, and had dealt with several family members' cremains that were heat-sealed in heavy plastic bags. It appears, therefore, that this clumping thing may be something of a myth.

I will continue to coat my urns with epoxy and prefer that the jars be epoxied shut (rather than doing a threaded removable cap) to prevent spillage. I think it will make a cleaner job than the plastic bag and twist-tie method. If you do small keepsake urns to be shared by/distributed to family members, I think the epoxy method will be far better to secure the cremains.

hth

Re: URNS

#11

Re: URNS

James Heaston EC Ohio

Just stick me in the ground in a burlap sack w/ an acorn in my mouth. ;)

Re: URNS

#12

Uh Uh

Mark Mandell - Gone Round In New Jersey

DNA etm is all destroyed in the cremation process. They'll just have to keep working on that phimosis cure without you, Bernie.

Re: URNS

#13

Re: Answer +

Bernie Rose

Thank you Mark. It is gratifying to get a straight answer to a question that had the potential for a multitude

of devious and smart-ass answers. I will print out your answer and keep it with my instructions for my heirs.

Considering that I can turn enough mini urns before I get demoted to "Chief inhabitant" of the one I have turned for my self.

Re: URNS

#14

Size?

ron bauer

Bernie, et.al., am I correct that the interior volume needs to be about 1 cubic inch per pound of the deceased? How do you size the urns?

Re: URNS

#15

Re: Size?

Bernie Rose

Ron: I do not do a great calculation on size related to the bulk of the decedent. My usual sized urn is based on a one gallon content capacity. This is over-kill in most cases, but if size is important to the customer a more accurate calculation can be used. Esthetics is probably the most defining problem in the size and shape of an urn, so be sure to get the customer involved in the design - ahead of time if possible.

Re: URNS

#16

Re: Size

Mark Mandell - Gone Round In New Jersey

There is a "standard size" of 200 cu. in. that is most commonly used for adult cremains. The 1 cu. in. per pound of live weight of the deceased is also used for custom urns. For instance, a 200 cu.in. jar would be far too large for a child and not nearly large enough for a 7' tall basket ball player.

Re: URNS

#17

Re: URNS

phillip Medghalchi

Bernie, can you post a pic. of one f your urns please, so we can see what you are talking about and how the size will work, and also, how do you get he customer involved in the design if you are designing on the fly?

Re: URNS

#18

One Design

Mark Mandell - Gone Round In New Jersey

For a burial urn, there was a good article in the AAW Journal in October 2012. If you are an AAW member, you can access it on line through the AAW website.

Re: URNS

#19

Re: One Design

Bernie Rose

I wish that Ellis would fix the problem of everything disappearing when I punch the TAB button.

Phillip: I don't post pictures and it should be obvious that one cannot get the customer involved if you are designing on the fly. If it is the measurement of the volume that disturbs you, get a one gallon can and fill it with rice. If the urn holds a gallon of rice it should hold a gallon of ashes.

Re: URNS

#20

Jim Evans

Re: URNS *LINK*

Jim Evans

Follow the link.


Look here.