Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

aluminum pipe for dust collector

Posts

aluminum pipe for dust collector

#1

aluminum pipe for dust collector

John Lucas

Well I got a new (to me) dust collector. It's a Grizzly 2 bagger 2300 cfm. I had an older Jet 1100 cfm. I have had all flexible pipe on that rig and wanted to go with as much rigid as I could on this set up for better air flow. I've used aluminum pipe on my older Powermatic which was 11 cfm with no problem and you can get this at my local hardware so that's what I used.

It won't work with 2300 cfm. I turn the dust collector on after spending an entire day running all new pipe. It worked fantastic and I had a heck of lot more air flow. was going to switch from the lathe to the bandsaw and close the gate and it collapsed the pipe on that line. open the gate back up and it opens back up somewhat. OH well, lesson learned. Went to town and bought some steel pipe today. Now have to spend the better part of the day tearing duct tape off and replacing all the pipe. Wasted day but I guess I learned something from it.

Re: aluminum pipe for dust collector

#2

Re: aluminum pipe for dust collector

Chuck Engstrom

Hi John -- I'm wondering if you put your gates where the pipe branches, rather than up close to the devices where it's going to draw, would that reduce the suction in that branch enough to prevent collapse? You'd probably have to open another branch first to keep the whole thing from being sucked into collapse.

Best --

Chuck

Re: aluminum pipe for dust collector

#3

Re: aluminum pipe for dust collector

John Lucas

chuck a lot of things might have worked but it was only $34 to replace the pipe. I'm almost done. Had to break for lunch. A friend came over and offered a suggestion on the dust collector placement that I had not thought about and makes a lot of sense so I'll probably do that later today. Will have to replace the power cord with a longer cord but it will be much easier to clean the bags out.

I've got to stop and fix the rear window in my car. For some reason it quite working yesterday. I hate power windows. Well OK sometimes I like them but I've had to replace the front 2 this last fall. It's a 2004 Honda with 164K miles. Don't you hate it when car repair gets in the way of woodworking.

Re: aluminum pipe for dust collector

#4

Re: aluminum pipe for dust collector

Bart Leetch

Was that suggestion to put it next to an outside door?

Re: aluminum pipe for dust collector

#5

Mike Stafford

Re: aluminum pipe for dust collector

Mike Stafford

At least you can recoup some of the expense for the aluminum pipe by selling the crushed pipe as scrap.

Re: aluminum pipe for dust collector

#6

Re: aluminum pipe for dust collector

John Lucas

Mike Actually I have a very tall ceiling and all my heat goes up there. I picked up a duct fan at a yard sale this fall but didn't have time to install it. Now I have almost all the pipe I need. I'm just going to pick up that heat and pump it back down to the floor through the pipe. :)

Re: aluminum pipe for dust collector

#7

Re: aluminum pipe for dust collector

Bernie Rose

I modified the 4 in intake on my Grizzly to take a single 6 inch PVC. problem is that I could not keep the dust bag on with so much pressure. So I by-passed the bag and ran the exhaust out through the wall of my pain locker directly to the outside where it nicely mulches the the gravel path. Much easier than cleaning up a sawdust covered bunch of paint and varnish cans.

Re: aluminum pipe for dust collector

#8

Question

Mark Mandell - Gone Round In New Jersey

John, what size pipe are you using?

I hope it's 6" because something less than that, with that size blower, is a huge waste and you'll be starving the impeller of air. DC's are not vacuum cleaners; the airflows are much different.

You'll need ducts that have a minimum crush resistance which is why I use 6" PVC S&D in my shop.

Re: aluminum pipe for dust collector

#9

Re: Question

John Lucas

Mark This one had an adapter for 3 4" hoses. That's what I'm using. Not sure I have room in my shop the way it's layed out right now for 6" pipe. I will certainly look at that option later when I move, which hopefully won't be too far off.

Re: aluminum pipe for dust collector

#10

Three-Fer

Mark Mandell - Gone Round In New Jersey

The triple port tells you that the blower is "designed" to pressurize three 4" lines at the same time. Aside from whether the Griz blower can actually do that, putting one 4" line to the intake will result in at least 66% loss in suction, probably more because of the resistance and friction in that 4" pipe. You're going to be running a 2-3hp motor but getting 1 hp or less worth of dust collection.