Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Question on turning a small rose vase.

Posts

Question on turning a small rose vase.

#1

Alan Sweet

Question on turning a small rose vase.

Alan Sweet

I want to turn a rose vase in which a a glass insert placed. This allows a flower to be watered in the vase. The insert will hold any water, be removable and will be 3/4" in diameter. The insert will be 5" long. The vase will not be more 2" in diameter. With a flare top, so that the insert in recessed about 3/8". A 13/16" hole is fine for holding the insert.

The sides at the top are about 1/4" thick, but flare out starting at the middle

and moving downward.

I need to make the hole for the insert 5 1/4" to 5 1/2" deep to provide the proper recess. I am having some challenges.

1. Bits really are not that long.

2. Forstner bits are not that long And that includes their point.

3. Spade bits are almost that long. I can put an extension on then.

Challenges.

Using a progression of bits, I can almost get the hole as deep as I want, but I have to use some longer tools to deepen the hole. This is interesting because getting the shavings and dust out, to test the insert, is not that easy.

I am getting wobble after making the hole and I can't seem to reset the blank so that it is flush in the chuck so that it does not have some sort of wobble. The wobble creates a problem in finishing and parting the bottom from the blank. And any final cuts.

I've tried using a deadhead live cone but since the sides are around 1/4" at the top, I can't use too much pressure.

When I prepared the blank, I cut a tenon and shoulder for the chuck to mate against. The tenon is about 3/4" long and the should about 1/2" thick.

OK, question. What are the suggested approaches I should use so that I don't get the wobble?

Re: Question on turning a small rose vase.

#2

Re: Question on turning a small rose vase.

john Veerkamp

When I turn small vases like this, I round off the blank and then bore the hole before any other shaping. I then finish turn the top around the hole. Be sure the insert fits. Put a cone center on the tailstock and center the piece well. Finish turning the outside and then part off the vase. Hand sanding the bottom is all that is left before finishing.

Re: Question on turning a small rose vase.

#3

Dennis in Southern Oregon

Re: Question on turning a small rose vase.

Dennis in Southern Oregon

Seems to me that if you can get an accurate hole nearly deep enough using a suitable bit, you can easily finish the job using a 1/2" square-nose or round-nose scraper or even a spindle gouge or bowl gouge used in a scraping mode. There should be no problem even if the bottom of the hole is a bit too large.

Dennis

Re: Question on turning a small rose vase.

#4

Rob Wallace

Re: Question on turning a small rose vase.

Rob Wallace

Alan:

These are the best Forstner bits on the market, IMHO:

http://www.woodturnerscatalog.com/p/4/-/16/76/-/4233/COLT-MaxiCut%C2%AE-Forstner-Drill-Bit?term=forstner%20bits

Bit extensions allow you to drill very deep, straight-sided holes:

http://www.woodturnerscatalog.com/p/4/-/16/76/-/4234/COLT-MaxiCut%C2%AE-Extension-Shank?term=bit%20extension

The system also has a Morse Taper adapter:

http://www.woodturnerscatalog.com/p/4/-/16/76/-/4235/COLT-MaxiCut%C2%AE-Morse-Taper-Adapter?term=colt%20maxicut%20mt%202

I use this system to drill peppermill blanks and to bore-out the center section of deep vessels and hollow forms - the bits clear chips easily and cut like a hot knife in butter in side grain and end grain equally. Easy to use, a "bit" pricey, but worth the money.

Hope this helps,

Rob

Re: Question on turning a small rose vase.

#5

Re: Question on turning a small rose vase.

Dick Coers

If you have a consistent diameter hole, you can make a pin chuck. Flip the vase around, and then return the od and base to true it up to the hole. Drilling end grain is always problematic since the bits have a tendency to follow the grain direction. You can also get an extensions for forstner bits.

Re: Question on turning a small rose vase.

#6

barry rockwell

Re: Question on turning a small rose vase.

Barry Rockwell

Alan,

Craft Supplies, and probably others, has a 3/4" drill bit that is plenty long for the glass insert, and has a M2 taper on the end so it will fit in your tailstock. To finish the bottom of the vase, place the bit in the headstock, slide the vase over it, and finish the bottom. Other size bits with M2 tapers also available.

Re: Question on turning a small rose vase.

#7

Lyle Jamieson

Re: Question on turning a small rose vase.

Lyle Jamieson

Use a bigger drill. As the wood shrinks and expands from year to year the wood movement will crush and break the glass insert. It should be sloppy in there. Been there done that.

Re: Question on turning a small rose vase.

#8

Convalco

Jorge

Alan, I am late and have not read the other posts.

I have several Convalco forstner bits, the original forstners, and you can get them in various lengths. A good investment too, they last and last. They are not serrated, and they are individually machined so they cost more

Convalco stands for Connecticut Valle Co.

Check them out, I used to get mine from Jamestown distributors.

Re: Question on turning a small rose vase.

#9

Brad Vietje

Re: Question on turning a small rose vase.

Brad Vietje

Sorry to come to the party so late -- any chips and salsa left?

Will your design allow you to drill all the way through? I would either do that, or drill a smaller diameter hole up from the bottom to allow water to drain out. Someone is sure to spill some fluid down that hole, and in warm and humid months the glass tube may sweat, and you'll have a lot of moisture getting way down deep inside your turning. Eventually, that could cause swelling or finish problems, like the paint peeling off a house from moisture getting in behind the clapboards.

If you drill it first, use the hole(s) to re-center the blank before turning the outer and inner profiles, coat the insides with thin epoxy, and provide some sort of weep hole to allow water to get out, I suspect the vase will last a very long time and never present any problems.

Safe spinning,

Brad Vietje

Newbury, VT