Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Turning Wearing Gloves

Posts

Turning Wearing Gloves

#1

Turning Wearing Gloves

Doug Reynolds

I was always taught not to wear gloves around power tools especially when flat woodworking, however, I see a number of woodturning videos where the turner is wearing gloves. As I age I may benefit from wearing shock absorbing gloves i.e., bicycle gloves. Is this practice generally approved in the turning world?

Re: Turning Wearing Gloves

#2

Doug,

GaryG in MD

You have touched upon one of the "sore" points where, as a community, we have to agree to disagree. Some say "no" for obvious reasons. Some say "yes" for equally obvious reasons. Some are in the middle with a "once in a while, just for certain applications". I'm in the latter group.

The simplest way to look at it is that a glove is a tool. Tools must be used appropriately, with understanding, and with proper care to be safe. I think that pretty much covers it. ...GG

Re: Turning Wearing Gloves

#3

Re: Turning Wearing Gloves

Philip F Duffy

When I am turning big ruff green wood and need protection for my hands, I use a leather glove with the finger tips cut off so I can feel the tool better. Since I often switch hands, both gloves are the same. OTOH, when turning a small dry wood for a box, or a pen, no gloves are needed or desired. - - -makes sense to me, and perhaps others. Philip

Re: Turning Wearing Gloves

#4

Re: Turning Wearing Gloves

Barry Irby

I agree with the above. I often wear a leather glove with the finger tips cut off on my left hand. I make a point for it to be tight fitting with nothing projecting or dangling from the glove. I also switch hands, but it seems the left takes most of the abuse so it gets the glove.

You can also wrap your tool handles with shock absorbing tape like on a tennis racket or other "shafts". Helps with cold too.

Re: Turning Wearing Gloves

#5

Re: Turning Wearing Gloves

John Lucas

Many wear fingerless gloves like bicycle gloves on their left hand. It keeps the hot chips from hurting your hand. In my shop during the winter it's simply too cold not to wear them. I work differently when I have them on. I don't get my hands anywhere near the wood when it's spinning. If I have to make a cut where my hands are close to the wood I remove the glove for that period of time. I know the dangers but it's either wear gloves or not turn, I choose to turn. Fortunately it's starting to get warm now so the gloves come off. I will wear the bicycle glove when turning larger dry wood pieces because the shavings hit my knuckle and hurt.

I really don't notice vibration being a problem.

Re: Turning Wearing Gloves

#6

Mike Stafford

Re: Turning Wearing Gloves

Mike Stafford

I have been wearing gloves a lot due to some nerve and cold sensitivity issues I am dealing with. I have never worn gloves before and wish I did not need to wear them now. I don't feel safe wearing them because I don't know where my hands are without paying close attention. If a glove gets caught in a spinning piece of wood I fear the party is over. So proceed with caution.

I cannot hold the tools in my hands without gloves now. They reduce the sensitivity and feed back I am used to receiving. I eagerly await warm weather so I can turn barehanded again.

Re: Turning Wearing Gloves

#7

Steven Antonucci

Agree with everyone *LINK*

steven antonucci

For me, I rarely wear them, and when I do it is only a single glove on my left hand during roughing. If you move a lot of wood and bark fast, it stings like hell the way I cut because the flute directs it into the back of my hand along the pinky bones. If it was just one chip, I wouldn't bother, but it is a steady stream of them for a few minutes and it starts to hurt pretty quickly.

I am very careful at all times with where my hands are, gloves or no gloves. It is a very conscious thing to me, so I don't consider it risky, but I see a lot of videos where the guy turning in them is wearing a glove and nowhere near as conscious of his hands. Like Gary G. said, it is another tool, and used properly, very safe and effective.

Used improperly, you can learn what the word avulsion means...

Steve


Avulsion

Re: Turning Wearing Gloves

#8

Re: Turning Wearing Gloves

robo hippy

Well, I used to have a bowl turner's callus on my left pinky finger. No more. Perhaps another benefit of using scrapers for my roughing is that it directs the shavings up more rather than across the top of my hand. I do stand a little to the side so I am not in the stream of shavings. Most postures with the gouges and the way you hold them send the shavings across your fingers.

One reason to keep the tool rest close to the wood is that with the shorter lever, there is less force sent to the handle. The left hand actually has almost no work to do. The white knuckle grip is very exhausting, and I still have to remind myself not to do it.

robo hippy

Re: Turning Wearing Gloves

#9

Thin leather golf glove works fine!


Re: Turning Wearing Gloves

#10

Bill Blasic

Re: Thin leather golf glove works fine!

Bill Blasic

I very much agree with Jamie as that is what I use. Thin, tight and nothing loose to catch on.

Bill

Re: Turning Wearing Gloves

#11

Re: Thin leather golf glove works fine!

Emmett Manley, Lakeland, TN

Another vote for a tight fitting thin soft leather golf glove on my left hand only.

Re: Turning Wearing Gloves

#12

Re: Turning Wearing Gloves

Steve Kniffen

After 30 years in the safety business, I know that "sometimes" is the right answer for a lot of questions. I wear fingerless anti-vibration gloves when I turn anything that's unbalanced or has a lot of bark to strip off. I've got 2 pair from Harbor Freight; http://www.harborfreight.com/1-2-half-finger-antivibration-gloves-large-95544.html#.UxpMj8485X4 . They fit tightly and 2 velcro closures on the back of the wrist make sure there are no pieces of glove loosely flapping so it can get caught. I have good feel with them and good mobility and tool control. At $10/pair they're really cheap insurance.

Steve