Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Inexpensive DIY Laser Depth Gauge

Posts

Inexpensive DIY Laser Depth Gauge

#1

Inexpensive DIY Laser Depth Gauge

charlie belden

The former president of our turning club president showed this inexpensive DIY laser depth gauge. Can really help to avoid turning a funnel. Won't work if you do miniatures, but . . .


Re: Inexpensive DIY Laser Depth Gauge

#2

Rob Wallace

Re: Inexpensive DIY Laser Depth Gauge

Rob Wallace

Charlie -

It looks like you clicked on the wrong file to embed in this message. The image we got was the same as one posted previously in your work holding thread.

Rob

Re: Inexpensive DIY Laser Depth Gauge

#3

Re: Inexpensive DIY Laser Depth Gauge

charlie belden

Rob:

Looks like the software is doing it again.

I checked my post immediately after posting and the the right image was there to see.

Checked just now and the right image is there.

So let's try a verbal description

Imagine an "F" and flip it horizontally so that the horizontal parts face left.

On the lower horizontal part of the backwards "F" there's a rubber conical tip

On the upper horizontal part there's a 1/2" T-fitting (think a T on its side)

A small pen sized laser is mounted in that T on its side pointing down towards

the rubber tip

The backward F is made up of 1/2" copper pipe fittings mounted on a threaded

metal pipe flange (think Face Plate) that's screwed onto a piece of 3/4", the latter

ply willl sit on the bed of the lathe.

The centerline of the lower horizontal part of the backward F is at the lathe

axis' centerline.

The whole thing can be mounted to the lathe in place of the tail stock.

When turning a bowl or hollow form, held in a chuck, the lower horizontal part

of the backward F can be inserted in the bowl or hollow form and slid towards

the headstock until it touches the bottom of the bowl or HF. The laser will

put a red dot ou the outside of the piece showing the location of the inside

bottom surface.

(A picture really is worth a thousand words)

Re: Inexpensive DIY Laser Depth Gauge

#4

Rob Wallace

Re: Inexpensive DIY Laser Depth Gauge

Rob Wallace

Thanks for the reply Charlie - I checked this on two different laptops and Android phone - unfortunately the incorrect image of the old chuck diagram is still there, and there is no image of the laser depth finder . Can you try posting it again? Rob

Re: Inexpensive DIY Laser Depth Gauge

#5

Alan Zenreich

Re: Inexpensive DIY Laser Depth Gauge

Alan Zenreich

I too see the image of the chucks

Re: Inexpensive DIY Laser Depth Gauge

#6

me 3


Re: Inexpensive DIY Laser Depth Gauge

#7

That's what I was thinking.


Re: Inexpensive DIY Laser Depth Gauge

#8

Let's try again

charlie belden


Re: Inexpensive DIY Laser Depth Gauge

#9

Alan Zenreich

Re: Let's try again

Alan Zenreich

Success, the photo now displays

Re: Inexpensive DIY Laser Depth Gauge

#10

Rob Wallace

TOUCHDOWN!!!

Rob Wallace

Thanks Charlie - Yes, a picture IS worth 1,000 words!

Rob

Re: Inexpensive DIY Laser Depth Gauge

#11

Bill Blasic

Re: TOUCHDOWN!!!

Bill Blasic


I bought this one off of Bill Grumbine, reasonably priced and can be used on different sized lathes.

Bill

Re: Inexpensive DIY Laser Depth Gauge

#12

Alan Zenreich

Re: TOUCHDOWN!!!

Alan Zenreich

Bill, I have the same Grumbine setup. I wonder if the copper pipe version needs the clamp in the base at all, as there is no need for one in our rigs, and it's not the kind of device one would want to lock in place... It's for a quick check.

Re: Inexpensive DIY Laser Depth Gauge

#13

Re: TOUCHDOWN!!!

Barry Irby

I like it, but I have built hundreds of things out of copper pipe and and I can't imagine it is "accurate" enough for this application. The fittings are rather loose and I think this setup would be way too "sloppy". If you soldered all the joints it would be more rigid, but still fairly flexible.

Re: Inexpensive DIY Laser Depth Gauge

#14

Re: TOUCHDOWN!!!

Steve Worcester.

In the photo, the beam wouldn't be completely perpendicular to the point, which will cause a problem in thin walls. You could probably use right angle framing clamps to align while you solder or Jbweld into place