Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Precision Router Mount on the Lathe

Posts

Precision Router Mount on the Lathe

#1

Precision Router Mount on the Lathe

Steve Criscenzo

I have some design ideas that require a precise mount for a router on the lathe. I finally had a bit of free time today so I spent the afternoon fabricating a two part system.

First I made a base that attaches to the bed of the lathe. The base is fitted with two "T" tracks so I can use it mount other jigs. (I have plans to make a router table similar to the John Lucas model that I can mount to the "T" tracks. There is a guide bar that fits between the ways and two bolts lock it in place.

To hold the router, I fabricated a mount that attaches to a cross-feed vise. The router mount bolts to the "T" slots in the vise so it can be move and adjusted. The cross-feed vise mounts to the "T" track base. The entire vise can be moved along the tracks and lock in place with the two knobs. The movement along the track plus the two axis adjustment on the vise give lots of adjustment. (I also have a design for a rotating base in mind that will allow mounting the vise at an angle.)

I did a trial with the setup this afternoon. Worked like a champ.

What was fun was, that being the pack rat that I am, I was able to construct the entire unit with material at hand. I salvaged the cross vise from a trash pile a long time ago knowing that someday I would find a use for it.

If my design ideas come to work out, I will post the results.


Re: Precision Router Mount on the Lathe

#2

Re: Precision Router Mount on the Lathe

ron bauer

Steve, I like it, A LOT!!. One question is there any vertical adjustment or is it designed to cut on the center line? Ron.

Re: Precision Router Mount on the Lathe

#3

Re: Cuts on center

Steve Criscenzo

It is set up now to cut at the center line of the lathe. I have a couple extra plexiglass plates to mount it at different heights if the need arises.

Steve

Re: Precision Router Mount on the Lathe

#4

Re: Precision Router Mount on the Lathe

Dick Coers

Isn't that plexi really flexible? I'd think you would need some gussets back to the base to keep it precise.

Re: Precision Router Mount on the Lathe

#5

Re: Precision Router Mount on the Lathe

John Lucas

Good job Steve. I e been looking at sort of the same thing but I want to add some sort of rotary table. Let me know if you find any problems. I won't be able to do any more work on my set up for a while. Too much else to do

Re: Precision Router Mount on the Lathe

#6

Re: Flex Control

Steve Criscenzo

Dick

You are correct, there is a bit of flex in the plexiglass. I made a simple cradle out of a short piece of 2x4 and slid it under the router and it worked well. I may replace the plexiglass with a piece of 1/4 aluminum now that I have the concept in place.

Steve

Re: Precision Router Mount on the Lathe

#7

Re: Flex Control

John Lucas

I use little right triangles off the sides You will find that even aluminum will flex. Another alternative is to make the base out of 3/8 or thicker plastic and route out an opening for the router. That will reduce the flex a lot. You can buy 12x12 sheets of various plastics from www.use-enco.com

Re: Precision Router Mount on the Lathe

#8

Re: Thanks John

Steve Criscenzo

Thanks for the link John. I will let you know when I get the rotary base made.

Steve

Re: Precision Router Mount on the Lathe

#9

KISS principle

Geoff Whaling

Steve, looks good.

I use a router on the lathe quite a bit and have made simple router sleds that ride on a table mounted on a tool post in the standard banjo. The sleds are not much more than a timber "L" bracket with a hole drilled with a forstner bit then cut through on one side, in the long grain, to permit clamping the trim router or Dremel firmly. I use temporary gibbs from boards clamped to the table. Tounge & groove floor boards make great guides.

The issues & concerns I have had with similar setups to yours, is with too slow travel of the router cutter across the timber causing burning. This occurs with even brand new sharp HQ router bits on our hard and well dried Aussie timbers. I have two X-Y tables, one cheapie that has all sorts of issues and is difficult to sort out with the gibbs adjustments. The other a much higher quality unit is very slow to traverse.

Re: Precision Router Mount on the Lathe

#10

Re: KISS principle

John Lucas

Jeff I've use my XY table on my drill press with router buts with great success. It runs slower of course but then I have variable speed modules for my router so that may not be a problem.

What I want to do of course is route on turnings and have more control over the router.

Re: Precision Router Mount on the Lathe

#12

Sweet-but I can barely use my Iphone 


Re: Precision Router Mount on the Lathe

#13

Geoff, more pictures?

Dick Coers

I did a fair amount of Google work, but only saw that short video. Do you know if there are any more links or even just pictures of his machine? I ran a 5 axis CNC at my day job before retiring. I didn't think I would care to run one during retirement, but his work is really inspiring! I'll send him an email as well.

Re: Precision Router Mount on the Lathe

#14

Re: Geoff, more pictures?

Geoff Whaling

Dick, unfortunately no. I have seen Dean's work on a few occasions but like quite a few very talented Aussie turners Dean has a pretty low profile on the WWW. He has his own gallery and some of his work goes through Bungendore Gallery, but that's about it. I would love to see his setup.