Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

I now have a variable angle drill bit.

Posts

I now have a variable angle drill bit.

#1

I now have a variable angle drill bit. 

John Lucas

A morse taper is designed to push not pull. I know many of you know this but thought it worth reminding. A morse taper is designed to be pushed against. When drilling holes on the lathe you should get into a habit of holding the chuck when pulling the drill out. Also clear the drill frequently so it doesn't bind in the hole. this and vibration can loosen the chuck and make it come loose in the tailstock.

I was doing photos for a future article this morning and had to let the drill chuck loose while I worked the camera. I'll be I've done this many times and this is the first time I've ever had it come loose on my. Fortunately it only did repairable damage to the workpiece but as you can see ruined my drill.


Re: I now have a variable angle drill bit.

#2

Steven Antonucci

Save it for drilling multi-axis holes


Re: I now have a variable angle drill bit.

#3

Rob Wallace

Sell it to Escoulen or Barbara Dill....


Re: I now have a variable angle drill bit.

#4

Ah

Mark Mandell - Gone Round In New Jersey

The truly rare Hula Hole bit.

1 hoop or 2?

Re: I now have a variable angle drill bit.

#5

If you cross your eyes it looks straight


Re: I now have a variable angle drill bit.

#6

Lyle Jamieson

a fix

Lyle Jamieson

I drilled a cross hole in the tailstock quill with the Jacobs chuck in it. Now put a pin in it. I use a door hinge pin. No risk of the drill being pulled out of the morse taper. No need for precision, just use a hand drill right on the lathe. I think it is risky to hold the chuck or drill by hand. If it starts spinning it could get dangerous.

Re: I now have a variable angle drill bit.

#7

Re: a fix

John Altberg

What a great idea, Lyle! Do you ever have any difficulty aligning the holes?

Re: I now have a variable angle drill bit.

#8

Lyle Jamieson

Re: a fix

Lyle Jamieson

No. Make the hole slightly bigger than the pin. This is just an emergency stop pin. A little slop in the hole will not hurt. The morse taper does all the work. The pin just stops it from spinning if the chuck pulls away from the quill.

Re: I now have a variable angle drill bit.

#9

Re: a fix

John Lucas

Good idea I'll bet I've drilled a 1000 holes or more with all sorts of bits and never had a problem other than occasionally it would spin. However what you suggest stops all of that and may even help on the rare occasion that a drill bit gets stuck.

Re: I now have a variable angle drill bit.

#10

Lyle Jamieson

Re: a fix

Lyle Jamieson

Works especially well with Forestner bits that tend to bind up if you get in a rush and push them too hard. Go faster in green wood too.

Re: I now have a variable angle drill bit.

#11

This reminds me....and another thought

Barry Irby

My first thought was: This is a great idea!

My next thought was, but I don't want to be drilling holes in my tail stock. (If God had meant for there to be a hole in the tailstock, he would have put one there.)

It reminds me of the story about the guy who bought the $500 shoes. They were beautiful and he was very proud of them but they were killing his foot and he was limping. They were seriously pinching his toe. His friend told him to cut a little slit in the shoe to make more room. He said, Are you kidding, I paid $500 for these shoes? Yeah, but they are killing you. Few days alter he is walking fine. The friend asks about it and he says Last week I would not have taken $500 for these shoes, now I would not take $500 for the cut in them.

Another thought is that if you don't want to drill through the tailstock, you could install a draw bar on the chuck. Drill and tap a hole in the end of the taper and run a piece of all-thread through the tailstock. Put a washer and nut on the rod hand tight. I have some set up for my head stock.

Re: I now have a variable angle drill bit.

#12

Re: This reminds me....and another thought

John Lucas

That won't work. Most people crank the tailstock quill in to drill the hole. You can't do that if you have a drawbar essentially connecting the quill to the handle in the back. :)

Re: I now have a variable angle drill bit.

#13

Lyle Jamieson

No Lathe police

Lyle Jamieson

There are no Lathe Police lurking around your neighborhood. I give you permission to drill a harmless hole in your tailstock quill. The manufacturers don't use the lathes. They don't know how valuable and easy the hole is to use compared to a draw bar. Many of us have made suggestions to manufacturers to improve the use of lathes and most suggestions get ignored. Even if lathe manufacturers drilled the hole for you, the user has to finish the job by drilling the hole through the chuck in the Morse taper.

Re: I now have a variable angle drill bit.

#14

I was befuddled, as is often the case....

Barry Irby

I visualized drilling through the tailstock and the quill. I was reluctant to dill through the casting. Later I realized it was only the quill. I think that's better. Might have to reach inside and polish away any roughness left by the drill, but that would not be bad.

I don't understand how the drawbar would get in the way. You would want the rod to be "just right" and not stick out too far and smooth up the end, but it would be in the way of spinning the wheel on the Tail stock. At least not much.

Re: I now have a variable angle drill bit.

#15

Lyle Jamieson

Re: I was befuddled, as is often the case....

Lyle Jamieson

There is no burr on the inside the mating male and female surfaces comes out clean. The exit hole on the bottom will have a burr to clean up, the entry and exit is easy to clean up on the outside of the quill.