Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Turning a Walnut Pedestal on General Spindle lathe

Posts

Turning a Walnut Pedestal on General Spindle lathe

#1

Chris Groves

Turning a Walnut Pedestal on General Spindle lathe

Chris Groves

I need to turn a pair of heavy solid walnut pedestals for a DR table I am building. I have glued up my blanks 8 x 8 inches by 22" long. I am questioning if my spindle lathe is robust enough to safely turn these large walnut pedestals.

Here is my General spindle lathe (weighs 175 lbs with 32" bed extension)... It is mounted on heavy metal stand . It is basically a heavy duty mini format lathe. It has a 3/4 HP variable speed motor.

http://www.general.ca/products/1_general/25_lathe/25-200.html

Since the blanks weigh 35 lbs I am a bit concerned that I may be overtaxing my machine...

I am an experienced turner... I also do a lot of large bowl turning on my Vega 2600 bowl lathe. I have done plenty of spindle turning but have not turned any large pedestals on this lathe before.

If I am careful to slowly true up the blanks is this a safe operation or should I turn these on larger and heavier lathe.

Thanks for your input.

Chris

Re: Turning a Walnut Pedestal on General Spindle lathe

#2

Re: Turning a Walnut Pedestal on General Spindle l

Barry Irby

Are they hollow? Just wondering, I'm too cheap to donate enough walnut to make them solid.

I would not hesitate to turn them. Just start off slowly. Keep the speed reasonable. The lathe will tell you. Don't do what I used to do. I had a light weight lathe and if I turned an out of balance piece it would "walk" around until I got it balanced. Sometimes I would end up several feet from where I started.

Re: Turning a Walnut Pedestal on General Spindle lathe

#3

Chris Groves

Re: Turning a Walnut Pedestal on General Spindle l

Chris Groves

solid walnut... 3 planed pieces of 12/4 glued up to make these $$$ pedestals

Re: Turning a Walnut Pedestal on General Spindle lathe

#4

Re: Turning a Walnut Pedestal on General Spindle l

Dale Miner

Will the glue up clear the banjo? Knocking the corners off with a table saw will help out not only in clearing the banjo, but also in the amout of time and force required to get the piece round.

Re: Turning a Walnut Pedestal on General Spindle lathe

#5

Worse case scenario

John Lucas

I had to do something beyond my lathes capabilities that was similar. Once it was roughed out it ran smooth enough to handle it but my minimum speed of 600 was to high when it was rough and out of balance. I had a friend stand by the switch. He turned it on a d when it got fast enough to shake he turned it off. I roughed it out as it was coming up to speed or slowing down. Didnt take long to get it balanced and running

Re: Turning a Walnut Pedestal on General Spindle lathe

#6

Re: Worse case scenario

Bill Howatt

I had a very low power lathe that looked like a clone of a Jet 1236. It's low power allowed me to do what you did without a helper. If it started to shake, a heavier cut quickly slowed it down enough to stop it. I used to think it was a problem, maybe it was a feature!

Bill

Re: Turning a Walnut Pedestal on General Spindle lathe

#7

Chris Groves

Re: Worse case scenario

Chris Groves

I already took off the edges with 45 degree cuts on my TS so I will give it a shot at 300-400rpm to rough it out... I should be able to handle it... thanks for all the great feedback

Re: Turning a Walnut Pedestal on General Spindle lathe

#8

Just be sure you have it securely....

Barry Irby

mounted. On stuff like this I sometimes use a forstner bit or even a paddle bit to drill a hole that is the size of my drive spur and maybe a half inch deep. You could do the same on your tail stock center. Then I mount it, cinch it down, run it for a few seconds and cinch it down again. Stand out of the way and flick it on and off to bring it up to speed slowly until you have confidence. Of Course turn it a revolution or two by hand before turning it on at all.

Re: Turning a Walnut Pedestal on General Spindle lathe

#9

Chris Groves

Re: Turning a Walnut Pedestal on General Spindle l

Chris Groves

Great idea Barry... I do not want this piece to have the chance to move around one iota...I will drill recesses at both ends with forstner bits that match my centers

Re: Turning a Walnut Pedestal on General Spindle lathe

#10

Re: Turning a Walnut Pedestal on General Spindle l

Stuart Johnson

I have glued up my blanks 8 x 8 inches by 22" long.

According to the specs the distance between centers is 17 5/16. How are you going to handle the extra length?

Re: Turning a Walnut Pedestal on General Spindle lathe

#11

Learned it the hard way....

Barry Irby

Years ago I cut down and oak tree in my yard that lightening had struck and killed. I hacked a blank out of it for a hollow form. The blank was about 7" in "diameter" (it had about eight sides) and was 14" long. I was tired but decided to turn it to a cylinder to get a better look at it. I usually put my face shield on with my right hand and then turn the lathe on with my left. The left got ahead of the right and the piece flew off and hit me right between the eyes on my forehead. Twenty seven stitches alter I was back home.

I really don't know what happened, but I think the end was not square and the spur center only seated on one of two wings. Not smart to turn when you are tired and inattentive. I still have the hollow form. (I can't sell it for enough to get the $1300 for the stitches back.) That's when I started to drill the recess for the spur. Gets you a nice flat bottom that is square to the axis and the surrounding shoulders.

Re: Turning a Walnut Pedestal on General Spindle lathe

#12

Bed Extension

Bill Howatt

He says he has the 32" bed extension.

Bill

Re: Turning a Walnut Pedestal on General Spindle lathe

#13

Chris Groves

Re: Turning a Walnut Pedestal on General Spindle l

Chris Groves

Success.... after cutting the 90 degree edges off on my TS with a 45 degree blade cut at max blade projection I used a hand plane to balance the blanks blanks to keep the lathe happy.

Even though this worked out well I may still have a used 3520 in my future as soon as I can expand my shop space.

I had forgotten how nice walnut is to turn. I will post a pic of the finished pedestals in a few days.

Re: Turning a Walnut Pedestal on General Spindle lathe

#14

Brad Vietje

Good Idea

Brad Vietje

That's a great idea, Barry.

I think you can also use a sharp bowl gouge or 1/2" spindle gouge and rough turn it in smaller bites for less cutting resistance. I pretty commonly use a 1/2" spindle gouge to rough a square to round in many small bites instead of using the roughing gouge.

Once you get it running as fast as it can go w/out walking across the shop, the flywheel effect will also help keep it running, so you probably won't hurt the 3/4 hp motor doing this.

Good luck and safe spinning,

Brad Vietje

Newbury, VT