Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Thread Chasing Mesquite

Posts

Thread Chasing Mesquite

#1

Thread Chasing Mesquite

Cyril Griesbach

I'm learning to hand chase threads in order to demo this for our club in February. I've been successful threading PVC pipe and hard maple with both male and female threads but the ones in maple are not as clean. That's most likely due to the nature of the wood. I do have some 2x2x6 Mesquite blanks that could be used for practice and the demo so I'm wondering if the collective wisdom out there can advise me what to expect when trying it in Mesquite.

Re: Thread Chasing Mesquite

#2

Steven Antonucci

I thread maple in side grain, not end grain

steven antonucci

try it... see if you like the results better.

S

Re: Thread Chasing Mesquite

#3

Re: I thread maple in side grain, not end grain

Randy Gleckler

Does this work with other woods as well? (I've been messing with some threading lately too and always looking for ways to improve it)

Re: Thread Chasing Mesquite

#4

Steven Antonucci

Short answer (Yes)

steven antonucci

not all woods take hand threading well. You need to try different bits and decide what works for your standard. White Oak, hard maple thread pretty well in side grain...

S

Re: Thread Chasing Mesquite

#5

Re: Thread Chasing Mesquite

John Lucas

I haven't tried Mesquite yet. I'll try to do that tomorrow. I think I have some try Mesquite somewhere. You need reallly hard woods. Boxwood and blackwood are the best. I use Cocobolo a lot and it threads well. Osage Orange does. I haven't used a lot of other woods yet. I still have trouble threading maple but I think it's because I don't have any hard maple. On a lot or our local woods the threads just crumble.

One thing I do is to cast epoxy into a groove in the wood. Then I can chase threads into this. You have to plan your project of course because the female and male threads have a slightly different diameter when your cutting your grooves to pour the epoxy. If I don't color the epoxy I try to leave a little wood on the inside of the male threads and outside on the female. Then the epoxy picks up the color of the wood. If I want to accent it then I color the epoxy Black or whatever color works for my project.

Using the epoxy lets me make my boxes out of woods I can afford to buy like Walnut, Cherry, etc. I also dry a lot of box blanks out of local woods and almost all of them are too soft to chase threads. That's why I purchased the Baxter threader from Bestwoodtools. You can cut threads in very soft woods using the powered cutter and the Baxter threader. Yes it's a lot of money but I just made a bunch of boxes and went out and sold them to pay for the unit. It is the best unit on the market.

Re: Thread Chasing Mesquite

#6

Re: I thread maple in side grain, not end grain

Cyril Griesbach

Thanks, Steve. I'll give it a try.

Re: Thread Chasing Mesquite

#7

Re: I thread maple in side grain, not end grain

John Lucas

If you try any of the softer woods like maple use a lubricant. I use Johnson's paste wax. Mark StLeger uses Dawn dishwashing liquid. It does help but I think the skill is still needed to do these woods.

Re: Thread Chasing Mesquite

#8

Re: Thread Chasing Mesquite

steve worcester

I think it with straight grain it would work well, but a little tear out since it isn't a full interlocking grain. But this comes from someone who doesn't thread.

Re: Thread Chasing Mesquite

#9

Cyril, a quick application of thin CA ....

JamieDonaldson

...will significantly reduce chipping and tearout on softer woods when chasing threads, even on side grain. Mesquite can often be crumbly when threading, so soak the area with CA and it will cut much cleaner.

Re: Thread Chasing Mesquite

#10

Re: I thread maple in side grain, not end grain

Cyril Griesbach

Thanks, John. I've seen Mark thread but I don't recall the Dawn trick. Maybe he didn't use it because he was using boxwood.

Re: Thread Chasing Mesquite

#11

Re: I thread maple in side grain, not end grain

Cyril Griesbach

Jamie, I tried some medium CA with no luck so I'll have to drive up to Woodcraft for some thin. While I'm there I'll also try to pick up some more suitable wood(s)

Re: Thread Chasing Mesquite

#12

Re: I thread maple in side grain, not end grain

Jim Breeden

John: How do you de-wax or de-dawn after cutting the threads?

Re: Thread Chasing Mesquite

#13

Re: I thread maple in side grain, not end grain

John Lucas

I don't do anything. I just wipe it on and then cut my threads. It acts as a lubricant. I haven't had any problems with my two favorite finishes, Lacquer and Wipe on Poly.

Re: Thread Chasing Mesquite

#14

I looked, didn't have any dry Mesquite *LINK*

John Lucas

I tried turning threads in Mesquite that was to wet to read with my meter. It worked but they had crumbly edges. If it worked in wood that wet I would bet it would work in dry wood.

Call Pete Kekel of Big Monk Lumber. He has talked to a lot of turners who use his woods for threading and will have some good advice. I bought some Katalox last time I saw him but it's still partially green so I haven't tried to thread it yet.

Ebony is also a good wood for threading.


http://bigmonklumber.com/index.html

Re: Thread Chasing Mesquite

#15

Re: I thread maple in side grain, not end grain

Ralph Watts

Cyril,

Jamie's suggestion was a good one. I have been using CA for a long time while threading less than perfect wood. I would only add, soak the threads after every pass. On many woods the CA will not soak in very deep (I do use accelerator) and after a couple of cuts it is mostly gone. Best regards, Ralph

Re: Thread Chasing Mesquite

#16

Re: Thread Chasing Mesquite

Josh Bowman

Mesquite is what I learned to thread on. Just the wood at hand, but I got very clean threads with it.