Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

question about WBP

Posts

question about WBP

#1

question about WBP

GaryG in MD

I am having a problem with Minwax water-based poly.

I use it sometimes when I can't use oils because I don't want to turn the wood yellow.

1) I do not shake the can.

2) I apply it with a real brush, not a foam thing on a stick.

3) I apply it slowly and carefully with sweeping brush strokes.

So why am I complaining?

Because I am getting tiny tiny bubbles, and some of them never pop.

That means every time I put on a coat, it has these little pimples that have to be sanded off. It's a royal PITA.

I can't understand what, if anything, I'm doing wrong.

Is this just a downside with this product?

I'd be interested to hear about your experiences if you've used this stuff.

Back to Dr. Who...

...Gary

Re: question about WBP

#2

Need more info

John Veerkamp

How old is it? What temp is the wood, the poly and the air?

Re: question about WBP

#3

Harry Robinette

Re: Need more info

Harry Robinette

I'm with John more info would help. The one thing I'll say is I quit using Min-wax about 6 years ago and am having much better luck with General Finish Stain,Poly,Oil's everything. Also I use a Camel Hair brush.

Re: question about WBP

#4

Re: question about WBP

Wes Pilley

Try blowing on it gently with a heat gun. Sometimes your hot breath will pop them.

Re: question about WBP

#5

more info

GaryG in MD

It's a new can, and the temp of the air and wood and finish are all around 65F, very much within the desired temp range.

Wes, the bubbles are very tiny -- way too small to "pop" -- and that's the problem.

Harry: I've been meaning to get some GF, but right now, this is what I'm working with.

...GG

Re: question about WBP

#6

I never use a brush. Just wipe it on

John Lucas

I get a fair amount on a rag and wipe it on. Then I go over it and wipe off any excess. I use a out 4 or 5 coats depending on how I want it to look.

Re: question about WBP

#7

Re: I never use a brush. Just wipe it on

John Lucas

I should have said that I use the wipe on poly. I be never. Even able to bush on any finish that didnt require rubbing out afterwords to create a good level glass tips finish. That's why I went to multiple layers of rub on finishes or spray lacquer

Re: question about WBP

#8

I've had similar problems with......

JamieDonaldson

...the Woodturners Finish, and the more you brush the worse it bubbles. The only solution I know is more sanding and rubbing out the zits.

Re: question about WBP

#9

Sanding Sealer

Jorge

By design all wood has pores on it, some more, some less, so that is where the bubbles come from, use sanding sealer, sand, maybe sanding sealer again, sand and then coat.

Re: question about WBP

#10

what species of wood?

Dick Coers

Open pore woods will get air trapped in the cells and work it's way out as the finish dries. Often leaves a bubble on the surface.

Re: question about WBP

#11

John,

GaryG in MD

This is not a wipe-on finish. The directions call only for brushing.

However, because of the problems I'm having with it, I might consider trying to wipe it. Thanks for the idea. ...GG

Re: question about WBP

#12

Jamie,

GaryG in MD

Well, that's not the answer I hoped for, but I guess it's the way it is.

I guess spraying would be a better way to go in general, but I can't spray anything now because it's too cold outside, and I don't have an indoor spray booth. ...GG

Re: question about WBP

#13

Jorge,

GaryG in MD

That's not the case here. The bubbles form even on a sealed surface. They apparently come from the interaction of the brush bristles with the surface. This stuff must have a very high surface tension, because the bubbles are tiny, and they don't all break as the finish dries (and it dries very quickly). ...GG

Re: question about WBP

#14

Dick,

GaryG in MD

You are correct. I've had that problem in the past, but it's not the case here -- the bubbles form even on a smoothed, sealed surface. ...GG

Re: question about WBP

#15

Re: Dick,

Dick Coers

Personally, I don't have much confidence in most of the Minwax products. I'd try some General finish if I were you. This time, you will have to do more post finish work to get it leveled out and looking good.

Re: question about WBP

#16

agreed

GaryG in MD

I've been meaning to try GF.

This is a good time. ...GG

Re: question about WBP

#17

Re: Jamie,

Terry

A piece of nylon stocking works well for applying a finish

Re: question about WBP

#18

Re: question about WBP

David Gilbert

I have also had problems with small bubbles in my some of my finishes although I am using Minwax Antique Oil (MAO). I am applying this with a reasonably high quality artist's brush on a well sealed bowl and the small bubbles cause roughness that I don't like. When this happens, I resand to smooth the surface and then I reapply the MOA with a small piece of folded lint free paper towel. The surface levels and gives a nice gloss without the bubbles.

Good luck and cheers,

David