Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Remotes for dust collector and air compressor

Posts

Remotes for dust collector and air compressor

#1

Remotes for dust collector and air compressor

Jim H

I have been meaning to go into town and pick up a remote from WC and just have not been that direction. Was at Home Depot noticed these in with the Christmas lights, they are rated at 15amp (not sure what my motors are, but they work fine with no heat detectable). Your mileage may very ;-)

At $17.88 each and a few blocks from home, it sure beats the $70 something I had planned.


Re: Remotes for dust collector and air compressor

#2

Re: Remotes for dust collector and air compressor

Mark Wollschlager

I used something like that ( a GE product for xmas tree lights ) on my dust collector.

It lasted a couple of years before it started flaking out. Starting up on it's own and sometimes not starting up the motor.

The relays wore out I guess. It was not overloaded, according to the motor specs, but I suspect that the startup current caused some arcing that wore it out.

I bought a long ranger and have not had a bit of trouble. It has been over 6 years.

Not having the thing turn on in the middle of the night or when I was out of the house is worth the extra expense.

Re: Remotes for dust collector and air compressor

#3

Another vote for the Long Ranger!


Re: Remotes for dust collector and air compressor

#4

Re: Remotes for dust collector and air compressor

robo hippy

I have had my Lone Ranger for 10 or more years. The only problem I had with it was that I lost my lone remote in the shavings. I got 2 to replace it. One is free range in the rest of the shop, and the one in the turning room is on a clip on the wall. They won't wear out.

robo hippy

Re: Remotes for dust collector and air compressor

#5

Re: Remotes for dust collector and air compressor *LINK*

Juergen

I've had my Long Ranger for 6 or 7 years. I've had to rebuild it twice after the plug got too hot and and fused to the power cord.

I've also used the following X10 products with good luck.

http://www.x10.com/hd245.html (220V, 20A)

http://www.x10.com/x10-home-automation/modules/am446-lamp-module.html (110V, 15A)

http://www.x10.com/x10-home-automation/modules/tm751.html (Controls the units above)

Juergen


X10 Switches

Re: Remotes for dust collector and air compressor

#6

Alan Zenreich

Re: Remotes for dust collector and air compressor

Alan Zenreich

I too use x10 based remotes in my shop to control my dust collectors. One dust collector has a 240volt appliance module, the other two are 120volt. They work well.

Re: Remotes for dust collector and air compressor

#7

Re: Remotes for dust collector and air compressor

Stuart Johnson

What is the remote range? I would like to add an outside light on the shop and be able to use a remote from the house to turn it on and off.

Re: Remotes for dust collector and air compressor

#8

Re: Remotes for dust collector and air compressor

Dale Miner

The hot plug problem seems to be common. Mine did the same and the plug was shot and needed a work around to get back to working order. The same happened to a friends, but was caught before total failure.

Otherwise, they are good outfits.

Re: Remotes for dust collector and air compressor

#9

Re: Remotes for dust collector and air compressor

Tony - Memphis

Lotsa variables that determine the range, but I do exactly what you are describing. Been working fine for many years. I added a motion sensor so that when I leave the shop, the sensor turns the lights on and then off after 4 minutes or so. Check eBay for some good deals on X10 stuff. My whole house and shop have multiple X10 gadgets installed.

Tony

Re: Remotes for dust collector and air compressor

#10

Re: Remotes for dust collector and air compressor

Jim H

Thanks for the input, I will keep an eye on these and maybe go to the X10 if they fail.

I do not like the idea of things coming to life while I’m away, but I think I have that covered already. When I leave the shop, I turn the sub panel off, that kills everything but the overhead lights and a charging station for all my cordless tools. This makes me feel better about power surges and accidental tool activations.

Re: Remotes for dust collector and air compressor

#11

Technically speaking

Bill Howatt

The devices to control motors should be based on a HP rating not a current rating since the motors are inductive loads with a large startup current and the tendency to arc when the relay (if present) contacts open.

You will often notice that devices to control resistive loads (an much easier load to control than inductive motor loads) will sometimes mention things like 15A resistive and a lesser value for tungsten because cold tungsten lamp filaments have a much lower resistance than hot thus creating a surge.

If the device works, it works but if it isn't rated for the motor HP then don't be too surprised if it fails early.

Bill

Re: Remotes for dust collector and air compressor

#12

Re: Remotes for dust collector and air compressor

Juergen

http://www.x10.com/x10-home-automation/controllers/wireless.html (Wireless controllers)

To add to my previous suggestion; The link above is for various wireless controllers. With these one can remotely control a number of switches with ONE controller.

I've not found the range to be an issue across a 3 car garage with interior walls.

Juergen

Re: Remotes for dust collector and air compressor

#13

Alan Zenreich

Re: Remotes for dust collector and air compressor

Alan Zenreich

The "range" is between the transmitter and the receiver. The receiver transmits its own signal through the electrical wiring to all the devices set to that channel and index.

Re: Remotes for dust collector and air compressor

#14

Dick Hines

Re: Technically speaking

Dick Hines

When I re did my shop I wired the dust collector switch on the wall behind the lathe. Since the DC is 220 I pulled a line off it for my Vac. pump. Since I don't run both at the same time it works great. The pump has it's own switch.

Re: Remotes for dust collector and air compressor

#15

Re: Remotes for dust collector and air compressor

h. phillip Medghalchi

Robo, did you mena the one form PSI for $20.00?

Re: Remotes for dust collector and air compressor

#16

Re: Remotes for dust collector and air compressor

robo hippy

I think the original came from Woodcraft, or maybe Oneida carried them then, which is where I got the dust collector from. The replacement came from Penn State. Can't remember the price though. They can start the DC from outside the shop.

robo hippy

Re: Remotes for dust collector and air compressor

#17

Re: Remotes for dust collector and air compressor

Don Evans

Elaborating what Alan said: for those who don't know X10 devises have 2 different directions of signal. From the hand held remote the signal travels through the air to a receiver module. The receiver module then sends a start up signal to all devices you have with it, in other words it can control more than one thing at the time. You set a switch on the module to 3 for example and another plugged in somewhere else to 3 and they will come on a off together.

One thing that will prevent it from working is a transformer in the electrical line. Say your house is one one transformer at the curb and your shop is on another output of the transformer goes to the shop. Usually not the case I think but if so then a turn on and off module in the shop and another in the house set the same will not work from one receiver. Confused yet?

You don't really need to worry about this part if your shop is on one transformer at the street and that is the only place you're using x10 devises.

Personally, I have not had good luck with x10, got one with my Onieda from Onieda and it failed in just few months. Have had a Lone Ranger (110 volt one) for over 15 years with no problem. The Onieda was 240 volt.

Got a remote from Woodcraft as needed one quickly for the Onieda the thing is yellow and don't know who makes it but I've seen it for sell from other places, same unit. First one lasted about 2 years and am not on the second one of same type, it is not x10 but a dedicated set up just for the Onieda. I use the Lone Ranger on an old Delta 580 with no bags on it that is connected to my tool sharpening grinder and it blows outside. Some of you may remember I put pictures of it on here many months ago, the piping, setup etc.

Don

Re: Remotes for dust collector and air compressor

#18

Re: Technically speaking

Barry Irby

Dick are they both 220? If you have 120 and 220 on the same circuit, Not good.

Re: Remotes for dust collector and air compressor

#19

Re: Remotes for dust collector and air compressor

Barry Irby

I have my DC wired on a Long Ranger relay that works on low voltage switches at each gate. Open the gate and the DC comes on. Usually. Burned one up. Got a replacement under warranty. Burned that one up later. Had a friend who is into such things rebuild it. He pointed out that the exterior of the unit said it was good for 1 1/2 Horse power motors, but the actual relay was only good for 1 horse power. I bought another relay that is much bigger and put that in the line. Now the Long Ranger relay operates the second relay and it operates the motor. No more problems.

Re: Remotes for dust collector and air compressor

#20

Re: Technically speaking

Don Evans

I don't see a problem with it IF you have a dedicated 240 line and tap one leg of it to run a small draw like the vacuum. I do the same thing and code doesn't care, not here anyway.

Why do you think it is not good idea?

I should add that my home run is 10 gauge 30 amp which the lathe is plugged into and it only called for 20 amp circuit (one way 2436). The vacuum is very small draw but cannot remember the amount right now.

Don

Re: Remotes for dust collector and air compressor

#21

Re: Remotes for dust collector and air compressor

Don Evans

I noticed that same thing many years ago. The relay was under rated but I (knock on wood) have never had a problem with it. Load of course has every thing to do with it and though the motor is rated at 1.5 hp it is a Delta foreign made motor and more than likely NOT really drawing the full 12 amp.

Maybe the back pressure on your dirty bags is causing it? (: ha :D

Don

Re: Remotes for dust collector and air compressor

#22

Re: Remotes for dust collector and air compressor

Barry Irby

How dare you Sir, My bag is not dirty....Oh! wait, yes it is. I really wish I lived somewhere I could eliminate the bag and just blow the stuff out in the woods. Why does anyone want a dust COLLECTOR?

Re: Remotes for dust collector and air compressor

#23

Alan Zenreich

Re: Remotes for dust collector and air compressor

Alan Zenreich

Barry,

With enough collected dust, and judicious use of glue, you can reassemble the wood into new turning blanks

Re: Remotes for dust collector and air compressor

#24

Re: Remotes for dust collector and air compressor

Henry W

I'd like to add to Alan's comment: "With enough collected dust, and judicious use of glue, you can reassemble the wood into new turning blanks"

Add just a little more dust and glue, top with some wood grained sticky plastic and you can make "furniture"

Barry, there's a whole industry built around wood dust

Henry