Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Rubber band chatter reduction

Posts

Rubber band chatter reduction

#1

Rubber band chatter reduction

John Lucas

I was turning more cupcakes today. when I turn standard boxes that are thin sometimes you get chatter out toward the edge when hollowing. On regular boxes I just dampen it with my fingers on the outside. Can't do that with the cupcakes because of the fluting on the outside. I put several rubber bands around the outside and it completely eliminated the chatter so I could get a clean cut on the inside.

Re: Rubber band chatter reduction

#2

This is a great tip.

GaryG in MD

You should send it to Betty. ...GG

Re: Rubber band chatter reduction

#3

Thank you John

John Stegall

Help for us mere mortals! Got a better shot of that "faceplate"?

Re: Rubber band chatter reduction

#4

Re: Rubber band chatter reduction

Barry Irby

Interesting! Wonder why it works? Mass? Something to do with the elasticity?

What speed were you running the lathe?

I am turning ornaments and one of them is a bell. (Bell with handle) I have found that to me it looks best if the bell looks right if the large diameter is the same as the height of the bell and the handle is about two diameters. I will try your idea on the outer lip of the bells to clean them up.

I was also thinking about a large rubber band to put around the chuck to keep the knuckle busters safer. Was wondering how fast you could spin them before they flew off?

Re: Rubber band chatter reduction

#5

Re: Rubber band chatter reduction

Hal Taylor

Fantastic find. Thanks for sharing. Chalk up another from John.

Re: Rubber band chatter reduction

#6

Re: Rubber band chatter reduction

John Lucas

Barry I don't know what speed I'm at because the readout on my older powermatic is just an arbitrary number. Pretty fast, probably 2000 rpm because these are small diameters.

Re: Rubber band chatter reduction

#7

Re: Thank you John

John Lucas

That was a boo boo. I cut this cupcake blank too short and was afraid I might hit the chuck with my router bit when fluting. I stuck a scrap piece of cherry in the chuck and turned a rebate into it that matched the tenon on the cupcake blank. glued the two together and it solved my problem.

Re: Rubber band chatter reduction

#8

Re: Rubber band chatter reduction

John Veerkamp

I use cheap vinyl electricians tape for the same purpose. Enough elasticity to dampen the harmonics.

Re: Rubber band chatter reduction

#9

Hey John, file for that patent ........

JamieDonaldson

...RIGHT NOW! I see a miracle marketing opportunity for "Chatter Buster Bands!" Every turner will want boxes and boxes of those special bands, in several colors and sizes! ;)

Re: Rubber band chatter reduction

#10

Keith Tompkins

Re: Rubber band chatter reduction

Keith Tompkins

Good one John. In the car business, a rubber belt is wrapped around brake drums while machining to cut down on vibration and chatter, and a narrow belt is installed around brake rotors for the same reason. I have used rubber bands on my turnings for the same reason...it works!

Re: Rubber band chatter reduction

#11

Re: Rubber band chatter reduction

Geoff Whaling

John handy tip. I tried it on my linear laminated bowls over the weekend & it does work to some extent. I was more worried about crushing the 1.5mm to 2mm walls of my bowls while putting the rubber band on the bowl.

Re: Rubber band chatter reduction

#12

Re: Rubber band chatter reduction

John Lucas

Goeff I suppose a lot of research could go into this from using multiple smaller bands to larger longer bands or even tying a bunch together to make big bands. Also how many are needed to and do more reduce chatter, or is there an optimum number.

I did some Bowl From board bowls that were 12" in diameter and somewhere around 2mm thick at the thinnest point. On those I hot glued "fan blades" to the outer porting of the bowl to reduce the chatter while thinning out the inside. I simply glued 4 smaller strips of wood perpendicular to the side of the bowl so it ran down the bowl and touched the chuck. It was amazing how well this worked. Very scary when you turned it on because it wirred like a propeller blade.