Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

buffing ca

Posts

buffing ca

#1

buffing ca

Darrin Hill

did some pendants that have some gaps in them that i filled with turquoise and ca.. tried buffing them on the beale system i have and i noticed the ca that filled the gaps between the chunks of turquoise was pitted... am i pushing too hard and removing it or is buffing ca bad to begin with?

have up to 2000 grit sanding pads then i buff with a paper towel which i've heard is equal to about 4000 grit sandpaper...and then i buff...

i use the 3 when tripoli, white diamond and carnuba on the pads..

Re: buffing ca

#2

Re: buffing ca

Darrin Hill

also doing 1800 rpms on the buffign wheels... probably melting the glue, but wanted to see what everyone else thought..

Re: buffing ca

#3

Re: buffing ca

steve worcester

Are they its or air bubbles in the CA?

Re: buffing ca

#4

Re: buffing ca

Darrin Hill

pits that i find AFTEr buffing... cause they are not there before... smooth surface..

Re: buffing ca

#5

Re: buffing ca

mjonesrdg

Darrin wrote"

"... am i pushing too hard and removing it or is buffing ca bad to begin with?]

It is difficult to diagnose the exact cause of the pitting you specifically describe. Generally, running a buffing wheel with tripoli wiil create heat which could be the cause of your problem. Apply heat to an adhesive bonded propduct and wierd things happen.

A year ago I switched over to Don Pencils gray buffing compound ....Use just the one wheel in place of the tripoli and the white diamond. I finish the process with carnuba buff and then renaissance Wax. Mr Pencil's compound is far superior for buffing finishes.

Re: buffing ca

#6

Re: buffing ca

David Walser

Darrin - It's hard to tell whether the problem is with your buffing or with the CA finish. CA finish, when applied improperly, can have small voids below the surface. So, your Tripoli buffing could lower the surface of the CA just enough to reveal those voids. However, it's hard to imagine that your sanding would NOT reveal any voids and your buffing would. Possible, but unlikely.

More likely, is that the heat from buffing was too great -- particularly if portions of the CA was not fully cured beneath the surface. When buffing CA, I use a lower speed, a lighter hand, and a finer compound (Don Pencil's PL compound). This approach has worked well for me. Using Tripoli, higher speeds, and too heavy a hand, sometimes left the finish with visible streaks.

I usually don't buff CA anymore. I've found going through all the grits with micro mesh and using a liquid buffing compound from the automotive parts store works just as well and is much faster. Everything's done on the lathe.

I also wet sand the CA finish starting with 320grit. It keeps the heat and dust down. Frankly, once I'm through with the last grit of micro mesh, I don't know that I need to use the polishing compound. Micro mesh is made for polishing the windshields on aircraft. If the scratch pattern is so fine that it leaves a finish good enough for a windshield, I doubt a liquid polish from the auto parts store is going to improve the finish much. I use it because I saw someone at a demo use it and because I have it.

Good luck!

Re: buffing ca

#7

Re: buffing ca

Bruce Pratt

Did you use accelerator on the CA? That can generate bubbles in the CA.

Re: buffing ca

#8

Plus one on the Don Pencil PL compund

mjonesrdg

I haven't used tripoli or white diamond in over a year since I got the PL compound and wheel from Don Pencil. I use it to buff lacquer, oil/varnish, CA, and any plastic (non-turned) things that I want to renew.