Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Angle Drill

Posts

Angle Drill

#1

Dick Hines

Angle Drill

Dick Hines

Well my angle drill just died. Now I have two dead ones. I went to the big box stores and found they only carry drills with a battery. Not a power drill in either store.

My compress is not big enough for an air drill. It may work OK if I was not using it to sand bowls.

Just ordered a new one. I may have to hold off finishing the bowl for a few days.

Re: Angle Drill

#2

Re: Angle Drill

Darryl

Try the "cheepes" at HF. Been running one for about a year with no problems

Re: Angle Drill

#3

Re: Angle Drill

Darryl

$29.95 and $34.99 on sale right now for the close quarter type.

Re: Angle Drill

#4

Re: Angle Drill

Dick Hnes

I ordered one that has sealed bearings. I think it comes with a couple of sanding disk manderals.

Re: Angle Drill

#5

Aage Rendalen

HF drills are the best deal

Aage Rendalen

I have five HB drills that I switch between when the one I'm using gets hot, and that way they last as long, I think, as the Milwaukees and other high-end ones. The HB drills make a lot of noise and I have to use ear protection, but they get the work done. Over the last four-five years I don't believe I have burned out more than two or three.

Re: Angle Drill

#6

watch for 20% off coupons

Ralph Lindberg

The "big city paper" has a flyer every couple of weeks that includes a 20% coupon and a coupon for a free item (usually a small LED flashlight)

You can also get fliers mailed or e-mailed

Re: Angle Drill

#7

Are we talking right angle or angle drills here?

Dick Coers

I didn't know Harbor Freight sold an angle drill. I've only seen the right angle ones. Link?

Re: Angle Drill

#8

Re: Angle Drill

Nick Todd

The Milwaukee/ Sioux lasted lest then a year, it's emergency replacement lasted four years (right angle drill).

Re: Angle Drill

#9

ditto


Re: Angle Drill

#10

Steven Antonucci

a different way of thinking

steven antonucci

why not buy a bigger compressor with a right angle air tool?

if you only sand bowls with it, it is probably a better option over time. I've used 2 right angle air tools in 10 years, and they were $20 ea.

Steve

Re: Angle Drill

#11

Re: a different way of thinking

DavidWalser

Steve,

The "right compressor" may cost more than $800 and might require 220v. That's what has prevented me from doing as you suggest. My one 220v outlet runs my lathe or my bandsaw. I could add an additional outlet to the circuit, but I've been told the compressor would trip the breaker if it came on while I was using the lathe. So, since the harbor freight cheapies can be had on sale for less than $30 and last more than a year, it would take a long time to pay back the investment in a new compressor/new 220v circuit.

Re: Angle Drill

#12

Steven Antonucci

I have a $150 compressor that runs on 110V?

steven antonucci

26 gallon tank, big box store brand... No special wiring.

Bought it to blow out hollow forms, plenty of air to power sand.

S

Re: Angle Drill

#13

Dick Hines

Re: I have a $150 compressor that runs on 110V?

Dick Hines

Steven, does your compresser have any trouble keeping up with your air sander?

Re: Angle Drill

#14

Steven Antonucci

If I run the compressor, not really

steven antonucci

I usually charge it up to 90 PSI or so, and I can get through most of a grit without it running. If I am in a hurry, I just start it and sand with shooting muffs on to cut the noise down. It fills almost as fast as it depletes, so I can sand an entire 15" bowl in about 15 minutes to 220 grit.

It sits 5 feet from my lathe, so it's kind of loud, but manageable with hearing protection and has probably delivered a couple of hundred bowls over the 5 years or so that I have owned it. I switch the sander for a blower to blow out the grits in between, so it's kind of convenient to have it right there. I would lose the blower if I had to put it in another room.

My next compressor will be purchased based upon how loud it is when it runs, but for now... this works well.

Steve