Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

epoxy questions

Posts

epoxy questions

#1

epoxy  questions

Darrin Hill

I do a lot of pendants.. like dick sing..

imagine, if you will... a pendant, turned, then drilled with a forstner bit all the way through..

then the hole would be filled with epoxy .. and i want to drop bits of turquoise in the epoxy.. but i want to try to keep them suspended instead of floating to the bottom...

tried with thick ca.. they floated to the bottom when the pendant was on its back... and it never dried properly

didnt know if a slow drying epoxy would work without them sinking, but a fast setting epoxy might trap bubbles...

one suggestion was to make the pendant, and then stick a plug onthe outside and seal it somehow so the epoxy would not leak out.. then remount on lathe and let it turn SLOWLY (suggested was 1rpm.. but my nova wont go below 100rpm.. so the turquoise bits would stay in suspension but then would bubbles stay trapped or... hmm..

and i dont have any epoxy yet, and actually have never used any.. but wanted ideas before i went out and bought the wrong thing..

Re: epoxy questions

#2

Re: epoxy  questions

John Lucas

Darrin the only way I know to do it, and this isn't perfect either, is to do it in layers. You didn't say if you wanted clear or colored. With color it would be easier. simply pour a layer and let it partially or completely harden. Then add some chips and pour another layer, and keep on going.

If you want it clear use acrylic casting resin, however You can sometimes still see the layers from certain angles. Casting resin is how they cast the fly in the ice cube. I played with it for a while and it works great and stays really clear but getting stuff to stay suspended is challenging. I tried stirring as it cures but of course that introduces bubbles.

Re: epoxy questions

#3

Re: epoxy  questions

Cyril Griesbach

Darrin,

I have no experience with this but a friend has had some luck by warming the casting resin before pouring it. He uses an inexpensive ultra sound parts cleaner from Harbor Freight that has a warming function. This is the kind of cleaner used, for example, on jewelery. I'm not sure how this would help with the suspension of your objects but it will help a lot with the bubbles.

Re: epoxy questions

#4

Re: epoxy  questions

Bill Howatt

I have limited (very) experience with a product called something like "Easy-Cast" that I got from Michaels in Canada. It was the smaller of the 2 products they had and I don't think the larger one is the same stuff.

It is very good for making bubble free casts by the application of a bit of heat from a hair-dryer. They also suggest the casting materials be above a certain temperature when mixing to reduce bubble problems. If your objects are too heavy they will sink and I think the layer trick suggested is what you have to do. I think this material is much easier to get a bubble free cast than using regular epoxy.

While this is a tremendous forum for answers, I suggest you Google resin-casting or epoxy-casting or similar. You'll likely find a lot more answers from people who do a lot of it.

Bill

Re: epoxy questions

#5

Layers + Vacuum

Mark Mandell - Gone Round In New Jersey

Hi Darrin,

Did some embedments years ago using epoxy. Couple of things to keep in mind.

1. Primary to any resin is to properly measure and mix the parts. Follow the manufacturer's direction to the letter.; get the proportions wrong and you'll have a lump of soft glop to throw away

2. Epoxy sets up by chemical reaction that generates heat; the more (thicker) the pour, the hotter it gets. Use a slow-setting hardener; fast-set creates more heat. Do not pour sections thicker than 1/2"-3/4" or excess heat will cause deformation during the cure and can actually boil the material which makes a real mess. You can even put the cast in a frig to slow down the reaction.

3. The easiest way to get air bubbles out is to put the mix into a sealable chamber and apply a mild vacuum. The air will foam out of the liquid and you'll get a crystal clear casting. Easy way to do this is with a 5 gal. bucket, a glass or plexi top, and either a vacuum pump (with bleeder valve) or a shop vac. The clear top is so that you can watch the process. You'll need to get a good seal around the rim of the bucket, and then make a fitting to connect the pump or vac. Pulling a light vacuum is usually enough to pull the air out of the mixed epoxy liquid. You can do this twice; once in the mixing bowl, and then again after you pour into the mold (or object). Caution: too much vacuum and the stuff will foam out of its container, making a mess. I usually apply the vacuum, get it to start foaming, release the suction to let the mix resettle, and do this several times until the mix doesn't bubble up.

4. You can put your embedments on one layer, or use more thin layers for greater depth. Pour each layer and watch as it starts to set up. A layer will get to the point where it will support your object, add the object, let it set, then pour the next layer, and so on.

The drawback to layers is that when viewed from the edge, the layers will refract light differently and the effect will be spoiled. There are processes to cast large/thick blocks of Lucite resin, however last time I looked into it the equipment was very expensive (well up in 5 figures).

Hope this give you some starting info.

Re: epoxy questions

#6

Re: epoxy  questions

Lan Brady

Darrin,

You might try the website of Beth Ireland. Ask her your question.

I have seen lots of her work with items suspended in castings.

Also the Penturners might be a good source to discuss preventing air bubbles.

Lots of Luck, Lan

Re: epoxy questions

#7

Re: epoxy  questions

cranskin

Lots of information on the Smooth On website regards casting resin etc.Probably more than you want to know. What you want to do is not that difficult,just have to use the right technique.

Re: epoxy questions

#8

Re: epoxy  questions

Dick Coers

Why drill all the way through and then worry about materials sinking? Just drill deep enough to get the minerals below the surface. As mentioned, casting resin is a much better choice. If you want a variable depth, use a silicon "cork" from the back side to set the depth, then add material to the back if you need it flush.

Re: epoxy questions

#9

Joe Fleming

Re: epoxy  questions

Joe Fleming

If drilled through to allow light, then fill the void from the back and let the items "sink" to the front of the opening. Joe