Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Questions on Lyle Jamerson's Hollowing rig

Posts

Questions on Lyle Jamerson's Hollowing rig

#1

Questions on Lyle Jamerson's Hollowing rig

Barry Irby

I have one of Lyle's hollowing rigs. I am trying to hollow what amounts to a sphere abut 10" in diameter. There will be a collar or neck on it. All was going well enough with the "straight" cutter set up. Tried to switch it to the offset version to hollow under the top or neck.

Anybody got a picture of the set up? I am trying to use the angled hole in the opposite end of the bar. Can't get it through the hole. What is the smallest hole it will pass though?

Also, the set screws keep loosening. Which type of Loctite is the one to use?

Re: Questions on Lyle Jamerson's Hollowing rig

#2

Re: Questions on Lyle Jamerson's Hollowing rig

Pete in Holland, MI

Hi Barry -

Mine is a home built from Lyle's plans so I can't help you on the angled cutter holder. Mine is only a straight cutter. There are some limitations with a system like this, and you may have discovered one.

Loose set screws?

Couple things:

1) are you driving the screw on to a round shaft, or have you ground a flat where it burrows into the shaft? This is key in keeping a shaft from rotating under a set screw.

2) If it is the screw loosening up, you need to tighten it tighter. If the shaft is rotating under the screw, deferr to item #1.

Good luck !

Pete

Re: Questions on Lyle Jamerson's Hollowing rig

#3

Re: Questions on Lyle Jamerson's Hollowing rig

Mike Squire

Barry, I happened to be looking at some of Lyle's videos on You Tube recently and one might be showing what you want. Take a look at 5:54 into the video.

http://www.youtube.com/watch?v=QnK6DUKn89g

Re: Questions on Lyle Jamerson's Hollowing rig

#4

Lyle Jamieson

Re: Questions on Lyle Jamerson's Hollowing rig

Lyle Jamieson

Hi Berry. For a sphere shape I use the bent swivel holder. It has a little bend but will reach the shape you describe. The little bend plus the movement of the swivel will get you there the easiest. I seldom use the "Big Bend" capability unless the shape has a larger diameter then it is tall and I still want to get into a small mouth opening. A help to you, if you still want to use the big bend configuration, is to put the back rest on the lathe backwards with the long portion in front. This allows you to get the start around the mouth easily. There are many other tips and techniques for getting into small mouth openings of any shape in my newest DVD, "In Depth Hollowing". Your turning club likely has it in the library. I have not found any limitations.

If you follow my directions in the se-up installation directions the set screws will not come loose. The trick here is to get the set screw in the middle of the flat spot you have under every set screw. I hope you are not forcing the tools beyond their capabilities and turning with vibration. Vibration is a no-no. Bad things can and will happen. You get the best results when you cut with the little hissing sound and no vibration.

Hope this is clear. If you are still having difficulties give me a call and we can trouble shoot your process.

Re: Questions on Lyle Jamerson's Hollowing rig

#5

Thanks....

Barry Irby

I am turning a nearly spherical shape. Its a piece of green maple from a damaged/rotting tree that was hollow with a sort of star burst pattern on the ends. What would have been the pith is oriented perpendicular to the ways, so that the openings come around on each revolution. I am getting vibration because the inside is so irregular. There is a lot of air in there with various fins of wood. I will try to be more gently and let the cutter do the work.

Thanks for the response. And thanks for posting the video on YouTube.

Re: Questions on Lyle Jamerson's Hollowing rig

#6

Lyle Jamieson

Re: Thanks....

Lyle Jamieson

You nailed it. Slow down and let the cutter do the work. Sharpen often!!

Is this one of those "life's too short to use crappy wood" examples. Be careful. Getting the speed up makes an easier and smoother cut but can be dangerous with weak wood. Check to see if you have good "bridges" for all the wood left. If there are cracks they must be small and supported by wood so that a big chunk will not come flying off at you.