Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Question for you box makers (Mike Stafford?)

Posts

Question for you box makers (Mike Stafford?)

#1

Question for you box makers (Mike Stafford?)

Mike Foster

I am working on a box (not my usual fare) for the SOFA show and was wondering what box makers find is the best finish for the inside. The issue is that most finishes will always carry an odor of the solvents/finish for a long time. I don't really want to leave it bare, but I could. This box is turned from cherry. My usual finish for the interior of a box was mineral oil and some wax but it seems like I remember someone doing a demo talking about using a drop or two of an essential oil mixed with perhaps mineral oil, which gives a very pleasant odor when opening the box. Any suggestions?

Re: Question for you box makers (Mike Stafford?)

#2

Mike Stafford

Re: Question for you box makers (Mike Stafford?)

Mike Stafford

Mike, I am sure there are as many opinions and answers to this question as there are wood turners but I will tell you what I do.

After sanding I apply while the box is still on the lathe several coats of brushable Qualalacq sanding sealer or lacquer thinned 50% using steel wool between coats to make sure it is smooth. After the lacquer is good and dry which only takes a few minutes I dust the interior and apply a light coat of Renaissance wax which leaves a nice odor in the box that I have never received any objectionable comments about. Buffed out this gives the interior a moderate sheen without being overly shiny.

There are some woods that I don't finish the inside of the box such as sandalwood, cedar, camphor if I think the odor is not objectionable.

Re: Question for you box makers (Mike Stafford?)

#3

Don Leydens

Re: Question for you box makers (Mike Stafford?)

Don Leydens

Hi Mike F., Mike S. told me about this lacquer finish and I tried it. Now, that's the way I finish all my boxes as well. It takes little time, looks great and smells just fine.

Don

Re: Question for you box makers (Mike Stafford?)

#4

I don't turn many boxes these days,.....

JamieDonaldson

...but "back in the days" I used a finishing routine similar to Mike's, and sometimes used a scented wax that was available from Big Monk Lumber(Pete Kekel) here in KY. He had several scents available, but I haven't noticed if they are still available from his web site.

Re: Question for you box makers (Mike Stafford?)

#5

angel tears finish?

Dick Coers

I would suggest no finish, but since you dropped the SOFA comment, it better have all the bells and whistles. Shouldn't it have hand hammered gold leaf, albino reindeer eye lashes, or double distilled angel tears in it to reach a price point? I mean you need something in that cherry box to be able to charge $2,000 for it!

Re: Question for you box makers (Mike Stafford?)

#6

Re: Question for you box makers (Mike Stafford?)

John Lucas

Mike Many of my boxes just have a wax finish on the inside. There's not a lot of wear on the inside and the wax makes it feel good and smell good. If I do finish the inside it's usually with thinned lacquer followed by the wax.

Re: Question for you box makers (Mike Stafford?)

#7

Re: Question for you box makers (Mike Stafford?)

Mike Foster

Thanks Mike, I kind of thought that lacquer would probably work. I don't have and Qual-laq, but do have rattle can and will probably go with that and some Ren wax. The box is already turned and I am working on the surface of the exterior. I'll post a pic of the piece when I get it done if I don't screw it up, but there is still a lot of work to do. It's not a "normal" box.

Re: Question for you box makers (Mike Stafford?)

#8

Re: Question for you box makers (Mike Stafford?)

Mike Foster

Thanks John. Like I just posted above, I think I'll go with a lacquer finish with a bit of wax.

Re: Question for you box makers (Mike Stafford?)

#9

Do you have a source for angel tears?

Mike Foster

I did consider a gilded finish but have not done any yet and did not want to experiment on this piece. I've already tried a bunch of new things on it (and screwed up 3 times requiring starting over). I love a challenge, but this one is really stretching me some.

Re: Question for you box makers (Mike Stafford?)

#10

Mike Stafford

Re: Question for you box makers (Mike Stafford?)

Mike Stafford

I look forward to seeing the results of your "not normal" box.

Re: Question for you box makers (Mike Stafford?)

#11

Re: Question for you box makers (Mike Stafford?)

Roger Chandler

Mike........I use a combination of 100% dewaxed shellac as a sanding sealer and base coat........after 2 coats of that, I lightly knock it back and apply about 4 coats of the General Finishes Woodturners Finish. [WTF] It will raise the grain a little as it is a water based finish, but then I just knock that down after the second and third coat, then apply the final coat.........it looks better the day after I finish it than it did when it was newly finished.......something about the way it cures and smooths as it dries completely.

It is a fairly quick finish that can have coats reapplied after 8-10 minutes and especially makes darker wood look good.

Just another option for you to consider, should you desire to do so.

Re: Question for you box makers (Mike Stafford?)

#12

Re: Question for you box makers (Mike Stafford?)

tomB

If you want a scented wax, Howard's Feed and Wax is beeswax and orange oil. I often use it for a salad bowl finish, and customers seem to like it

Re: Question for you box makers (Mike Stafford?)

#13

Re: Question for you box makers (Mike Stafford?) *LINK*

walta

This product smells a lot better than lacquer or shellac.

Walta


Lemon-Oil-Wax