Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

some mirrors just fight me

Posts

some mirrors just fight me

#1

some mirrors just fight me

John Lucas

I decided to make one more mirror before I go to Texas. Pulled out some purple heart with the intention of routing designs in it. The longer lines went perfectly. then I set it up to do the shorter lines. something slipped between the time I set it up and the time I made the first route. they went too long. OK not too bad there just isn't the contrast in size that I wanted.

So I continue to route. Now one of the problems with cutting this way is it's very hard to always cut downhill with the grain. so it chips out 2 different areas. so I figure I'll just turn those areas into a cove. Well that didn't work too bad but sure ruined the design I had drawn out. OH well it doesn't look to bad.

did I mention that I always measure my new mirror glass because it's not 4" any more. I did that and turned the opening before doing all the routing. I got finished, drilled it, put the handle in. Applied the finish and buffed it. got ready to put the glass in and it's .045" too large. Something slipped between me measuring the glass and using the calipers to judge the opening.

Now if I had a 3520B it wouldn't be a problem. I'd just chuck up the mirror, handle and all. Move the headstock to the end of the lathe and re turn the opening by moving the bed extension down and adding the tool rest. However I have a 3520A and don't have that option. The handle is 1" too long to clear the bed. I can move the headstock to the end but then I don't have a way to support tool. OH well. I'll use my head tomorrow and come up with something.

Re: some mirrors just fight me

#2

Alan Zenreich

Re: some mirrors just fight me

Alan Zenreich

Consider using a router to expand the space. You might need to use a circle jig, or perhaps make a circle template, and/or use a bit with a top mounted bearing

Re: some mirrors just fight me

#3

I could use my mill and rotary table.


Re: some mirrors just fight me

#4

Re: some mirrors just fight me

Stuart Johnson

Take it with you to SWAT and get Brent to let you use a Robust.

Re: some mirrors just fight me

#5

Re: some mirrors just fight me

Galen Vetterick

You start to slip a little in retirement, but look at it this way, you still made something out of it. When you get older in retirement you make slips and probably end with nothing out of it. I know! >(

It looks good to me---- as long as I don't have to look into the mirror side. :D

Re: some mirrors just fight me

#6

Dennis in Southern Oregon

Re: some mirrors just fight me

Dennis in Southern Oregon

John, you might consider sanding the mirror to size. Mount a sacrificial block in a chuck, turn it to a diameter just bigger than the mirror, cut a recess to hold the mirror, hold it in place with the tail stock and another disk of wood and sand the composite down to the required diameter.

Dennis

Re: some mirrors just fight me

#7

Re: some mirrors just fight me

John Lucas

I actually have lots of options. This has happened only about 3 times over the years and god knows how many mirrors I've made. Wish I had kept count.

I could use the router as Alan said. I'm really really good with a router. Use to use it for everything, long before I had a table saw, planer jointer etc. I used the router. Make a circle cutout and use a guide bushing with the jig clamped to the mirror.

I could move the tailstock to the end of the lathe and turn it on real slow and use the Dremel with a small sanding drum. The first time this happened I enlarged the opening with the Dremel by hand but rotating it on the lathe would be more accurate although it will try to enlarge the long grain more than the short grain.

I could use Mill with a rotary table which would be the most accurate method. Plus it has the option of mounting a dovetail cutter to undercut the opening so the wood has room to move.

then there's always the carving knife method. Since I only have to remove .023" all the way around it wouldn't take too long to do it by hand.

Re: some mirrors just fight me

#8

Re: some mirrors just fight me

Mavdad55

Make an outboard tool rest like Sam in Wyoming shows in this YouTube

http://youtu.be/ShQsQTbwXZI

Re: some mirrors just fight me

#9

Re: some mirrors just fight me

John Lucas

I built a floor standing tool rest a few years ago. Hated it. It just wasn't heavy enough and if you didn't have the bowl gouge positioned just right it would try and pull the tool rest into the work or at least created a lot of vibration. I made it from a truck rim but probably needed to fill it with concrete.

Vicmarc sells one like I want. It is a huge elbow sort of thing that attaches directly to the lathe and sits on the floor. It looks very solid. However by lowering my Bed extension like the 3520B does it will give me 30" of swing which is more than I'll ever need. I already bought the steel to make my tool post extension. Just have to find the time to drill and tap the legs to accept the bed extension.

Re: some mirrors just fight me

#10

Re: some mirrors just fight me

Barry L Elder

You say "it doesn't look too bad"! Geez man, you're the perfectionist personified! To me the consumer, it looks outstanding!! (without the glass) I'm sure you will do justice to the mirror part also! Have a great SWAT! :D