Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Any ideas

Posts

Any ideas

#1

Any ideas

Dale Bonertz

I rough bowls and kiln dry them. Yesterday I spent about 2 1/2 to 3 hours spraying anchorseal on the blanks and loading them into my kiln. In that time frame I only got about 40 to 50 blanks done because my compressor cannot keep up with me. At this rate if I have 150 to 175 bowl blanks I'll have 9 to 10 hours of spraying and filling the kiln, like last time I filled it. My compressor is 2hp with a 60 gallon tank which I know is a bit undersized but should be able to perform better than this. I tried dipping the blanks but it leaves much to thick of a layer of anchorseal and seems such a waste. If I water the anchor seal down for dipping do you think I'll I lose the benefit of the anchorseal? Is there something I can do with my compressor to be more effective? Or do you know of a low airflow sprayer?

Any ideas from this group of creative and experienced minds.

Re: Any ideas

#2

Re: Any ideas

John Lucas

Just put anchorseal on the endgrain areas and the foot and lip. Maybe that would reduce your overall usage. Can't help with the compressor. I just watched the local sales until I found a 5 horse, 100 gallon tank.

Re: Any ideas

#3

Re: Any ideas

Don Stephan

You might ask the maker of Anchorseal for sprayer and compressor suggestions.

Re: Any ideas

#4

Re: Any ideas *LINK*

Dick Coers

HVLP gun, separate additional compressed storage tank added in-line with your existing compressor, Harbor Freight sells an airless for less than $200, but cleaning lines would be horrible, and I've always been impressed with foam back pad painters. The foam really holds the material and it's faster than spraying when staining large surfaces. You would have to get a narrow one to coat the insides, but they are fast! Might even consider just using a glove and sponge, or a paint mit. The mits are less than $3 at Menards.


harbor freight airless

Re: Any ideas

#5

Re: Any ideas

Dale Bonertz

I just today while working thought about a paint sprayer similar to what house painters use. May have to look into that. Never really thought about the mitt only because you get used to doing it a certain way and some of those ideas don't cross your mind. Thus I guess why I asked the question.

John, I have considered doing what you suggested but to tell the truth it scares me to think I may lose a bunch of blanks. I probably wouldn't but when you work that hard to chainsaw, band saw, turn and core that many blanks and then step from your comfort zone and maybe lose a bunch is frightening. Next kiln I may try a handful that way and see how they do.

Thanks for the suggestions.

Dale

Re: Any ideas

#6

Re: Any ideas

Steve Worcester.

I have to wonder why you are anchor sealing blanks to put in the kiln. You may be forcing the schedule, and if the intent is to move them through faster,mother you have something that works. Spraying full thickness, use a gun designed to spray primer or bed liner. Probably any gun with a 1.8-2.0 will work, but I don't think HVLP guns can do that.

Re: Any ideas

#7

Re: Any ideas

Dale Bonertz

Steve, I am not spraying them to force the schedule at least not consciously. I learned this method from my good friend and mentor Dan Bailey. He purchased his kilns from Trent Bosch when Trent got out of production bowl turning. Trent taught Dan on his method of using the kilns and if I remember correctly told Dan to spray the entire blank because Trent had experienced cracking. Anyway that is what Dan taught me and it works so far. I can dry a kiln load (about 160 to 185) bowl blanks in four weeks or if really wet 5 weeks with no losses after two loads. This includes blanks with knots. This is also in my new kiln not the old ones where we were starting to lose a good 10% to 15% of the blanks.

Thanks for the gun advice, I'll look into it. I cut the anchorseal with water by about 20% to help with the flow. This kiln took about exactly 9 hours to spray and load it but it is full to the brim and 7 blanks I needed to stack on top of the dehumidifier in milk crates.

Re: Any ideas

#8

Steven Antonucci

Try in small batch

steven antonucci

Personally, I cored 100 blanks in apple, maple and cherry... generally close to 1" per 12" rule. I didn't coat any of them, only put them in big leaf bags to control the airflow around them. I lost 2. Even up to 16" in diameter.

Not sure what woods you are turning, but you may be able to get away with much less work?

Steve

Re: Any ideas

#9

Re: Any ideas

steve worcester

Well, the schedule is tried and true, so you can't really knock it based on your results.

Re: Any ideas

#10

Re: Try in small batch

Dale Bonertz

I think in the next kiln I am going to try your idea and John's idea. Not coat some and coat the end grain only on others. I won't do the whole batch that way since I don't have any history to pull from whether or not it will work.

My main and easiest supply is elm and maple. A little harder to keep in log stock is ash and locust but generally have some. Harder yet is oak, walnut, good mormon popular, willow and hackberry. This kiln load has elm, maple, ash, mormon popular, oak, walnut and locust in it.

Thanks for all the ideas,

Dale

Re: Any ideas

#11

Steven Antonucci

Trial is how I came to my observation

steven antonucci

I used to coat the entire blank by dunking it simply because it was way faster than painting them. When the kids got older, they wanted to paint... so I let them. I'd find bowls half painted with no cracks, and then I roughed some without sealing...

In NJ, I usually don't bother sealing... and I lose very few as long as I keep them in the heavier leaf bags. I don't think grocery bags work as well... but I don't know that scientifically.

When they crack, it is always end grain, so John probably has a point too...

Steve